A second order system has natural angular frequency of 2.Q rad/s and a damped frequency of 1.T rad/s. T= 4 (a) Calculate damping factor 100% rise time i. ii. nercentage overshoot

Q: if the system has amass = 2kg; c = 20N-s/m; andk = 200 N/m, What the category of mechanical…

A: Write the expression of the total spring equivalent.

Q: The solution to free vibration of a damped single degree of freedom system is 15 a. x(t) = Ae…

A: The solution of a free vibration of a damped single degree of freedom system is x=Ae-γwnt  sin1-γ2…

Q: 3. Calculate the natural frequency and damping ratio for the system in figure below. Assume that no…

A: Natural frequency = 40.25 rad/sDamping ratio= 0.00158 System is underdampedExplanation:Step 1:…

Q: Problem 4: For the gear system, find the damping D to yield a 20% overshoot in output angular…

A: Solution: Given Data:

Q: Fo/k ( sin (wt -ø) where y = damping ratio %3D

A:

Q: G(s) = 5(s + 5) (s+15)(s+8) G(s) = 15 s² +8s +32 G(s) G(s) s+3 s²+4 s+2 (s + 1)²

A: To Find:the system is undamped, critically damped, under-damped, or over-damped.the peak time,…

Q: Q.11- Consider the positions servomechanism is shown in figure below. Assume the following numerical…

A: Find outDetermine the natural frequency and damping ratio of the systemgivenGain of potentiometer…

Q: 5) The parameters for a one-degree-of-freedom system are M=10-kg. K=16- kN/m, and C=320-Ns/m. (a) By…

A: Given, Mass(m)= 10 kg            Spring constant(k)= 16 kN/m            Coefficient of damping(c)=…

Q: The following data pertain to a torque sensing transducer connected to the shaft of an electric…

A: The Answer is below

Q: Electric motor, dashpot, and spring system. The total mass of the system is 21.5 kg. The motor runs…

A: given:-total mass(m)=21.5 kgspeed(N)=500 rpmstifness (k)=6400 Nmdashpot offer 500N at 4.0 m/sec…

Q: HALL C J zk K A Sint Calculate the damping factor () with the following data

A: The force, F = 50 lb The deflection, e = 10 cm =3.937 in The stiffness, k = 220 lb/in The damping…

Q: Compute the maximum percent overshoot 100Mp and the 2% settling time ts that correspond to wn = 1…

A: To find: The value of maximum percent overshoot; The value of setting time. Given: The value of…

Q: Solve the forced harmonic oscillator for y(x). Then either give the steady state solution amplitude…

A:

Q: A single-degree-of-freedom damped oscillator with natural period, TO=1.0 s and viscous damping…

A:

Q: What is the deformation response factor for a damped system with stiffness of 800N/m, and a mass of…

A:

Q: (a) The position – time plot of a spring-mass-damper system is as shown - Find the damped frequency.…

A: Solution : From the position time graph the time period of damping = 3 sec The damped frequency is…

Strain Gauges

All the components used in civil engineering and mechanical engineering applications undergo deformations due to induced internal stresses under the application of external loads. Under repeated application of loads, there is a high possibility of failure of the components. Hence, periodic monitoring of the components and determination of stresses are very important.