A satellite similar to the Tethered Satellite in the figure below has a mass of 550 kg and is at the end of a 19.0 km long, 2.60 mm diameter cable with the tensile strength of steel. Tethered Satellite Return path through ionosphere (a) How much does the cable stretch (in m) if a 108 N force is exerted to pull the satellite in? (Assume the satellite and shuttle are at the same altitude above the Earth. Young's modulus for steel is 210 x 10° N/m².) (b) What is the effective force constant of the cable (in N/m)? | N/m (e) How much energy (in 3) is stored in it when stretched by the 108 N force?

A satellite similar to the Tethered Satellite in the figure below has a mass of 550 kg and is at the end of a 19.0 km long, 2.60 mm diameter cable with the tensile strength of steel. Tethered Satellite Return path through ionosphere (a) How much does the cable stretch (in m) if a 108 N force is exerted to pull the satellite in? (Assume the satellite and shuttle are at the same altitude above the Earth. Young's modulus for steel is 210 x 10° N/m².) (b) What is the effective force constant of the cable (in N/m)? | N/m (e) How much energy (in 3) is stored in it when stretched by the 108 N force?

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

The guy wires AB and AC are attached to the top of the transmission tower. The tension in cable AB is 9.2 kN. Determine the required tension T in cable AC such that the net effect of the two cables is a downward force at point A. Determine the magnitude R of this downward force. Assume a = 48 m, b = 58 m, c = 29 m, and d = 37 m. B Answers: 8 i T = R= a İMİ A b kN kN o d
Why is the degree wrong?
2. A strain gauge (see picture shown below from Omega) is a resistance element that is used to measure the fractional elongation experienced by a material. If it is attached to a beam that undergoes a deflection due to an impact, we can use the gauge to measure the deflection or monitor the frequency with which the beam vibrates. R1 SG1 wwwwww Lumin Assume we attach two strain gauges (SG1 and SG2) on opposite sides of the beam as shown above. If the beam deflects downward, SG1 elongates (so its resistance increases) while SG2 compresses (so its resistance decreases). Let's hook up the elements into a Wheatstone bridge as shown below. If R1=R2=100 92, and the nominal values of SG1 and SG2 when no strain is present are 100 as well, what is the value of Vout when the beam is deflected enough to cause SG1 to increase to 100.1 № and SG2 to decrease to 99.9 N? The voltage at the top of the bridge (10V in this case) is called the "excitation voltage". 10V Vout R2 Wall SG2 SG 1 SG 2 Beam
In the figure, a motor weighing 3000 N hangs on a chain attached by an O-ring to two other chains, one attached to the ceiling and the other to the wall. Calculate the tensile force acting on the chain attached to the wall. Consider that the weights of the chains and the ring are negligible.
15-8* A 20-kg block is pushed up an inclined plane by a horizontal force F of 200 N as shown in Fig. P15-8. The ki- netic coefficient of friction between the inclined plane and the block is μk = 0.10. If v = 0 and x = 0 when t = 0, de- termine a. The acceleration of the block. b. The time required for the block to travel 15 m up the incline. c. The velocity of the block after it has traveled 10 m up the incline. F 30° Fig. P15-8
upvote guaranteed
1
141 g wooden block moves with constant speed (on a table) when the total force applied is 15 g. What is the angle of repose?
As shown in the figure, a weightless rope is wound on identical cylindrical pulleys of mass m-5 (kg). What is the tensile force (N) on the rope when the system is released. The shaft of the spool above is frictionless. 10 (m / s?)
The 120kg homogeneous thin pla supported using ball and socket joint at E , a smooth roller at D. and a cable at O and B. Cable at OA acts axis while cable BC parallel to y - axis . If 700N force is vertically downward parallel to y - axis and a 400 Nm couple acts along x - axis are exerted on the plate , determine the tension of the cable at OA , BC and the reactions at D and E. The thickness of the plate is neglected .
Please answer fast
A model airplane with a mass of 0.65 kg flies at the end of a 60 m cable in the horizontal plane at a speed of 35 m / s. The aircraft connecting rope rotates at an angle of 20 degrees to the horizontal. what is the tensile force on the rope? The buoyancy force that lifts the aircraft is perpendicular to the wings. g=9,8