A sample of gas is taken through cycle abca shown in the p-V diagram of the figure. The net work done is +1.60 J. Along path ab, the change in the internal energy is +3.70 J and the magnitude of the work done is 5.60 J. Along path ca, the energy transferred to the gas as heat is +3.70 J. How much energy is transferred as heat along (a) path ab and (b) path bc?

A sample of gas is taken through cycle abca shown in the p-V diagram of the figure. The net work done is +1.60 J. Along path ab, the change in the internal energy is +3.70 J and the magnitude of the work done is 5.60 J. Along path ca, the energy transferred to the gas as heat is +3.70 J. How much energy is transferred as heat along (a) path ab and (b) path bc?

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

A gas is taken through the cyclic process shown in the figure. For one complete cycle, how much heat Q is transferred to the system given the points of interest shown in the chart? Pressure (Pa) Volume (m³) P = 3440 И 3 3.20 P3 9270 V2 7.35 Volume (m) 2. 3. Pressure (Pa)
The volume of an ideal gas is increased from 1 m3 to 3 m3 at a constant pressure of 1000 Pa How much work is done by the gas in the expansion? W= _________ J If no heat has been added or removed, what is the change in internal energy of the gas? DU = ________ J
A gas is taken through the cyclic process described in the figure. (The x axis is marked in increments of 2.5 m³.) P (kPa) 8 6 4 2 A B C -V (m³) (a) Find the net energy transferred to the system by heat during one complete cycle. kJ (b) If the cycle is reversed-that is, the process follows the path ACBA-what is the net energy input per cycle by heat? kJ
Helium (He), a monatomic gas, fills a 0.036 3 m³ container. The pressure of the gas is 5.3 × 105 Pa. How long would a 0.25 hp engine have to run (1 hp = 746 W) to produce an amount of energy equal to the internal energy of this gas? t = i
Suppose 6.70 mol of a diatomic gas is taken reversibly around the cycle shown in the T-S diagram of the figure, where S1 = 6.00 J/K and S2 = 8.00 J/K. The molecules do not rotate or oscillate. What is the energy transferred as heat Q for (a) path 1 to 2, (b) path 2 to 3, and (c) the full cycle? (d) What is the work W for the isothermal process? The volume V1 in state 1 is 0.420 m3. What is the volume in (e) state 2 and (f) state 3?What is the change ΔEint for (g) path 1 to 2, (h) path 2 to 3, and (i) the full cycle? (j) What is the work W for the adiabatic process?
The heat engine shown in the figure uses 2.0 mol of a monatomic gas as the working substance. (Figure 1) igure p (kPa) 600- 400 200 0 0 0.025 0.050 V (m³) 1 of 1 Part E part. What is the engine's thermal efficiency? Express your answer using two significant figures. η = Submit VE ΑΣΦ Request Answer ? %
A gas in a cylinder is held at a constant pressure of 2.20×105 Pa and is cooled and compressed from 1.90 m3 to 1.10 m3 . The internal energy of the gas decreases by 1.15×105 J. a) Find the work done by the gas. Express your answer in joules b)Find the amount of the heat that flowed into or out of the gas. Express your answer in joules to two significant figures. c) State the direction (inward or outward) of the flow.
As shown below, a nonideal gas goes through the cycle ABCA. During the process AB, 71.5 J of heat was added to the gas. During the process BC, 8.2 J of heat was removed from the gas. Determine WABCA & QCA. WABCA = QCA P(N/m²) 10 2 2 A 4 6 8 B с 10 V (m³)
You would like to raise the temperature of an ideal gas from 295 K to 960 K in an adiabatic process. a)What compression ratio will do the job for a monatomic gas? b)What compression ratio will do the job for a diatomic gas?