A round cross section cold drawn steel bar made of AISI 1020 has a diameter of 35 mm. Based on a conservative failure analysis, calculate factor of safety in the following conditions: a) The bar is subjected to static bending moment of 450 N.m, and steady torque of 180 N.m b) The bar is subjected to bending moment fluctuating between (900 N.m and 400 N.m), and steady tension of 2.4 kN

Q: A solid round bar with diameter of 2 in has a groove cut to a diameter of 1.8 in, with a radius of…

A:

Q: This problem illustrates that the factor of safety for a machine element depends on the particular…

A: Given, AISI 1006 cold drawn steel, F = 0.55 N, P = 4.0 kN, T = 25 Nm, yield stress, Sy = 280 MPa, D…

Q: Using the sample set of readings provided for Experiment 1 and taking the Young's Modulus of steel…

A: i hope its helpfull.thank you.

Q: Two Steel Rods (ASTM A36) and One Aluminum Rod (1060 0) are assembled to two rigid cover plates. The…

A: Two Steel Rods (ASTM A36) and One Aluminum Rod (1060 0) are assembled to two rigid cover plates. The…

Q: the ground and free in the upper end. a) Calculate the compressive stress, then the minimum…

A: Given Data: H=3 mm=1000 kgFOS=3σut,c=241 MPaE=190 GPa   To Find: (a) The compressive stress. (b) The…

Q: Using the sample set of readings provided for Experiment 1 and taking the Young's Modulus of steel…

A: i hope its helpfull.thank you.

Q: 1. Determine the diameter size of rods AB, BC and C if ay = 3600 MPa and the safety factor SF= 2.…

A: Determine the diameter size of rods AB, BC and CA, if Yield stress = Sy = 3600 MPa and the safety…

Q: 2. A l-in diameter rotating solid round bar has a groove 0.1-in deep with a 0.1-radius machined into…

A: Given data as per question Bending moment =1000 lbf. in f =0.9  q = 0.8 Calculations tensile…

Q: Q) A helical compression spring of a mechanism is subjected to Pas =120 N 19ad cycle. The diameter…

A: When a helical spring is compressed it experiences shear stress. Maximum shear stress is the sum of…

Q: 4. A stepped bar is subjected to an axial tensile force of 40000 lb. Compute the increase in stress…

A:

Q: the figure is subjected to a completely  reversed axial load fluctuating between 28 kN in…

A:

Q: 1. A cold-drawn AISI 1015 steel tube is 300 mm OD by 200 mm ID and is to be subjected to an external…

A: Given data - Outer diameter - 300 mm Internal diameter - 200 mm Yield strength = 600 Mpa It is asked…

Q: Figure 1 is a schematic drawing of a countershaft that supports two V-belt pulleys. For each pulley,…

A: Given data, For pulley A Tension in tight side, T1 = 103 N Tension in loose side, T2 = 0.15T1…

Q: A solid circular rod of diameter d undergoes a bending moment M= 1500 lbf-in inducing a stress o=…

A:

Q: The head of a 300 mm diameter cylinder vessel will be designed. The internal pressure in the…

A: Given data as per questionHead diameter(D)=300 mmbolt dia(d)=10 mmEb=200 GpaEm=90 GpaInitial…

Q: This problem illustrates that the factor of safety for a machine element depends on the particular…

A: Given DataP=4×103N {Axial Load}Sy=280MPad=15mmT=25N-mF=0.55kN

Q: Question 1 The steel cantilever beam shown here is subjected to a fluctuating Torque, T The part is…

A: Diameter of shaft, d=30mmReliability,R = 95%From the properties of AISI 1040 steel,for…

Q: ased on the yield stress rk out the allowable lo

A: A= 20x20= 400 mm2 Yield strength = 250 MPa F(s) = 4 Allowable stress = ? Working load =?

Q: Q1) Figure 1 shows a shaft mounted in bearings at A and D and having pulleys at B and C. The forces…

A: Given:Here are the given data,To find:The minimum shaft diameter.

Q: 4. A ductile cast iron chain to operate in a furnace used to fire ceramic bricks. The chain will be…

A: (a) Write the given formula for the Larson-Miller parameter. Lm=T100036+0.78ln t Here, T is the…