A room is maintained at 20°C by removing heat at a rate of 3 kW. The required power input to the air conditioning unit is 1.5 kW. Determine the COP. A For question 4 above, determine the rate of heat rejection to the outside air in kW.

Q: The 12-kg wheel has a radius of gyration k = 200 mm (Figure 1) Figure A M Y Part A If the wheel is…

A: According to the given data m=12kg kA=200mm=0.2m M=5t  t=6 sec We need to find Angular velocity…

Q: 5. The following table shows joint position coordinates for the hip, knee, and ankle during a single…

A:

Q: A M12 x 1.25 hex-head bolt with a nut is used to clamp two 25-mm thick steel plates. The nut height…

A: Given:- Elastic modulus 207 GPa Bolt size= M12 x 1.25 Height of nut =10.8 To find:- d) Bolt…

Q: A steel shaft is subjected to a fluctuating torque, T, as shown below. All surfaces are machined,…

A:

Q: Review Replace the loading by an equivalent resultant force and couple moment acting at point 0.…

A: We have to replace the load by equivalent forces and couple moment about point o. Consider the…

Q: Part A and B please

A: The load applied P is .

Q: Task IV A metal block of weight 10 N in air and 2N in water fully submerged in water. Given the…

A:

Q: An ideal Otto cycle has a compression ratio of 9.1. At the beginning of the compression process, air…

A: GivenAn ideal autto cycle r=9:1=9P1=100kPaT1=25oCQ23=1000 kJ/kg

Q: Figure VC 0.3 m 0.2 m B 1 of 1

A: Given: VB = 3 m/s VC = -1.7 m/s

Q: Learning Goal: To apply the condition of equilibrium to three- dimensional systems and solve for…

A:

Q: In the truss structure shown below, all members except the central one are perfectly rigid. The…

A: GivenE=1 GPa=109 Pam=1 kgA=1cm2=10-4 m2L=30cm=30×10-2 m∆L=0.01 cm=0.01×10-2 mAskedT=?FormulaG=TA∆LL

Q: a,b,c please and thank you!

A: The objective of the question is to determine the maximum and minimum principal stresses and the…

Q: 2. Shown below is the binary lead-tin phase diagram from your textbook. Answer the questions below.…

A: a. Proeutectic composition is calculated at the temperature just above eutectic line of 183°C As the…

Q: Prob 2. The cantilever beam below is made of steel (E200 GPa) and must support the distributed load…

A: To Find :  a) The location and magnitude of the maximum bending moment and draw the V and M diagram.…

Q: 1: Derive the two Tds relations from the energy balance. a. The first Tds relation and the second…

A:

Q: A person on horseback is on a drawbridge which is at an angle e = 20.0° above the horizontal, as…

A: Data given- Theta = 20° d= 1.30 m l = 9.50 m Mass of the bridge  = 2350 kg Mass of horse and perosn…

Q: The rod has a diameter of 40 mm. It is subjected to the force system F₂ = 1300 N, Fy = 600 N, F₂ =…

A: The rod diameter d =40 mm = 0.04mThe force systemFx= 1300NFy= 600NFz= 900NFindThe Normal stress act…

Q: Similar to the question in Part A, a hollow cylindrical 4130 steel tube has a 25 mm outside…

A: Vertical loads at A and B = 500 NFa = 2500 N torsional moment, T= 350 Nm Length L = 900 m outer dia.…

Q: A gas undergoes a thermodynamics expansion process as shown in Figure 1. Process ab represents the…

A:

Q: Air is driven from a reservoir at 1.3 MPa through a converging-diverging nozzle with a design Mach…

A:

Q: Bending Stress A cantilever beam of length 1.1 m carries a uniformly distributed load w, as shown in…

A: Length of the beam (L): 1 mUniformly distributed load (W): Given but not specified, please provide…

Q: The shaft shown in figure supports two gears. The shaft is made 600 mm from high carbon steel…

A:

Q: 1. The heat equation describes the flow of thermal energy (heat) in materials. The temperature V…

A:

Q: Y Part B - Clockwise Rotation of a Stress Element with Only One Normal Stress The state of stress at…

A: Note:- As per honor code and answering guidelines I can answer 1st question at a time.If you want…

Q: The jet aircraft has a total mass of 21 Mg and a center of mass at G. Initially at take-off the…

A: Given data with variables. m=21 Mg=21×103 kg2T=6 kNT'=2.1 kN   It is required to determine the…

Q: The two uniform thin discs shown in the figure rest on a horizontal plane and are connected through…

A: In this question, it is asking about the solution of part B only so we will provide the solution for…

Q: q4 part a plz provide handwritten answer asap

A: u asked only a part only so answer in hand written

Q: Consider launching a projectile from a cannon as shown in the diagram below. This arrangement has…

A: Initial vertical component of velocity = v sin θ also from the basic equations of motion we know…

Q: Table 4: Fatigue data of a ductile cast iron Stress Amplitude Cycles to Failure 1X 105 (MPa) 248 236…

A: a) The SN curve for the given data can be drawn as:   The above given is the SN graph for given…

Q: A mass of one slug is hanging at rest on spring whose constant is 12 lb/ft. At time t = 0, an…

A: Given:mass, m=1  slugspring constant, k=12 lb/ftf(t)=16 cosωft

Q: Determine the magnitudes of FA and Fg so that the resultant force passes through point O of the…

A: Given DataFR=FA+FB+8+6 FA=?FB=?

Q: ▼ Determine the necessary value of the spring constant k (Figure 1) Express your answer with the…

A: The unstretched length of the spring is x=350 mm. The normal force lever ABC exerts on smooth…

Q: Problem L7.3. Now that we have a basic understanding of Simulink, we can begin to simulate some…

A:

Q: In the 3D spatial problem below, force F is represented by dimension locations and has a magnitude…

A: Given:

Q: Consider a mechanical system consisting of two metal plates and two springs, connected vertically as…

A: The masses of the metal plates are m1, m2. The spring constants are k1,k2. The original length of…

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.