A rod of dimension 20 mm x 20 mm is carrying an axial tensile load of 10 kN. If the modulus of elasticity is 250 MPa, then the strain induced due to this load would be

Q: An aluminum bar having a cross - sectional area of 150 mm2 carries an axial load in three sections…

A: Given Data,  Length of AB= 0.8m Length of BC = 1m Length of CD=0.6m

Q: a bar is 500mm long and is stretched to 505 mm with a force of 50kn.the bar is 10mm diameter.…

A: Given data : Initial length=500 mmFinal length=505 mmForce (F)=50 KNDiameter (D)=10 mm

Q: If a Young's modulus of elasticity of a material is 210 GN/m and stress is 210N/mm, the strain in…

A: Given data : Stress (σ)=210 N/mm2Youngs modulus of elasticity (E)=210 GN/m2

Q: A steel column has a sectional area of 0.126 m^2 and a length of 3 m. IF a 50000 KN load is applied…

A: Given data, Column sectional area A = 0.126 m^2 Column length L = 3 m Force applied F = 50000 kN =…

Q: A steel of cross-section area 100 mm² and 1 m long is subjected to a tensile force of 40 kN. What is…

A:

Q: A 10.0 mm diameter cylindrical specimen of a bearing bronze material is pulled under uniaxial…

A: given-10.0 mm diameter 1500 N force∆d=0.67 mmn=0.35

Q: Determine the strain if stress value is 33 MPa and modulus of elasticity is 80 MPa

A: Given data : The value of stress σ=33 MPa The value of modulus of elasticity E=80 MPa   To find :…

Q: 2. What refers to the stress in the material at the elastic limit? 3. What is the ratio of the…

A: Elastic limit is the limit by virtue of its  material regain its original shape and size…

Q: The tensile test was carried out on a steel bar of length 18 cm and a cross section of 18 mm in…

A: Schematic diagram of the given problem: Maximum permissible tensile stress σ=400 N/mm2 E=200×103…

Q: ng steel bars, which was given a tensile strength of 45150 N, elongated by 2.1 mm, cross-strain was…

A: Given:- elongation=2.1mm E=200000MPa Poisson's ratio = 0.32 strain = 0.00056 To find:- a)L b)A

Q: A quantity which represents the ratio of the lateral strain to the longitudinal strain for a…

A:

Q: A 10 inch long silver wire is stretched to a total length of 11.50 inches. Find the value of strain

A:

Q: Assume if the shear stress in steel exceeds about 4.00 x 10^8 N/m2 the steel ruptures. (a) Determine…

A: Given : Allowable shear stress = 4 X 108 N/m2 Diameter of steel bolt = 1.05 cm Diameter of hole =…

Q: Assume if the shear stress in steel exceeds about 4.00  108 N/m2 the steel ruptures. (a) Determine…

A: Given:- The limiting value of shear stress in steel = 4.00×108 N/m2  The diameter of the steel bolt…

Q: Find the poisson's ratio for a given material if the modulus of elasticity is 100 GN/m2 and it's…

A:

Q: A steel section as shown in figure is subjected to a shear force of 20 kN. What will be shear stress…

A:

Q: What is the volumetric strain in the thin cylinder subjected to internal pressure having hoop stress…

A: Thin cylinder- Hoop stress=200 MPa, E=200 GPa, Poisson's ratio=0.25 Volumetric strain=?

Q: Determine the modulus of elasticity of material that has proportial stress 110 MPa and proportional…

A: Given data : The value of stress σ=110 MPa The value of proportional strain ε=0.002   Required :…

Q: Volumetric Strain Question 5: The principal stresses at a point in an elastic material are 60 N/mm²…

A: Given- Stresses- σx=60 N/mm2σy=20 N/mm2σz=-50 N/mm2E=100×103 N/mm2μ=0.3 Volumetric strain=?