A rod made of Unobtanium with a square cross-section is protrudes from a base surface of the same material that is at a constant temperature of 25°C. The rod has a side length of 15mm and a length 0.6m. The ambient air is at 125°C and has a convective heat transfer coefficient of 100 W/m²/K. Assume convective heat transfer from all surfaces of the rod. Determine the temperature at one-third of the rod length. Unobtanium Thermal Conductivity: 175 W/m/K T: 125°C h: 100 W/m²/K T: 25°C 15mm 15mm

A rod made of Unobtanium with a square cross-section is protrudes from a base surface of the same material that is at a constant temperature of 25°C. The rod has a side length of 15mm and a length 0.6m. The ambient air is at 125°C and has a convective heat transfer coefficient of 100 W/m²/K. Assume convective heat transfer from all surfaces of the rod. Determine the temperature at one-third of the rod length. Unobtanium Thermal Conductivity: 175 W/m/K T: 125°C h: 100 W/m²/K T: 25°C 15mm 15mm

Essentials of Business Analytics (MindTap Course List)

2nd Edition

ISBN:9781305627734

Author:Jeffrey D. Camm, James J. Cochran, Michael J. Fry, Jeffrey W. Ohlmann, David R. Anderson

Publisher:Jeffrey D. Camm, James J. Cochran, Michael J. Fry, Jeffrey W. Ohlmann, David R. Anderson

Chapter5: Probability: An Introduction To Modeling Uncertainty

Section: Chapter Questions

Problem 33P: Suppose that Motorola uses the normal distribution to determine the probability of defects and the...

See similar textbooks

Similar questions

A steel rod 20 mm in diameter and 120 mm long is joined to the end of a copper rod 20 mm in diameter and 80 mm long, thus forming a composite rod of 200 mm in length. If the ends of the composite rod are now clamped, calculate the stress set up in the steel and copper due to a temperature increase.
1. The projection of the liquidus surface of the ternary system A-B-C is given below; a) Draw the isothermal sections at 400°C and room temperature. (20p.) b) For composition X, what is the amount and composition of solid phase at its solidus temperature? What would you suggest to increase its amount by keeping temperature constant? (20p.) A (705°) B (924°) A.B 569° 547° 850 650- X 550- 513 $450 460° 550 500 484° 400° 500- 550- -650- 600- 750- Yo A3B2C 2B.C 736° 683° B.C wt.% 660° A3C 580° A6C (684°)
A mixture with the system given below is fed to a flash distillation column operating at 20 bar and 70 C. Calculate the compositions and flow rates of the streams leaving the column. components Amount (kmol/h) ethane propane N-butane i-butane n- pentane 15 25 25 15 20
C (Ib/gal) - 5.8. A mixing process may be described as follows: A stream with solute concentration Ci (pounds/volume) is fed to a perfectly stirred tank at a constant flow rate of q (volume/time). The perfectly mixed product is withdrawn from the tank, also at the flow rate q at the same concentration as the material in the tank Co. The total volume of solution in the tank is constant at V. Density may be considered to be inde- 2.1 2.0 1.9 1.8 1.7 W FIGURE P5-8 10 6:30 A.M. Time 6:52 A.M. pendent of concentration. A trace of the tank concentration versus time appears as shown in Fig. P5-8. (a) Plot on this same figure your best guess of the quantitative behavior of the inlet concentration versus time. Be sure to label the graph with quantitative infor- mation regarding times and magnitudes and any other data that will demonstrate your understanding of the situation. (b) Write an equation for C; as a function of time. Data: tank dimensions: 8 ft high by 5-ft diameter Tank volume V: 700…
1. A protein chromatography column that processes 15 kg of protein in 60 h, is cycled every 6 h, can be loaded with 10 grams of protein per liter of column volume, has a maximum flow rate of 50 liters/ min at a pressure of 4 bar, and is packed with an incompressible resin having a particle diameter of 90 μum and void fraction of 0.35. The viscosity can be assumed to be that of water. i. What are the dimensions required for the column? ii. If the flow rate is 1 column volume per minute and the pressure rating is still 4 bar, what column dimensions are required? Is the resolution equivalent to that for Part (i)? 111. If the pressure rating for the column were raised to 12 bar, should the column dimensions change? Is so, what should the dimensions be? Do they make sense? iv. What is the best way to increase the productivity of the column packing?
typing
At -8.64 °C the concentration equilibrium constant K = 7.7 for a certain reaction. Here are some facts about the reaction: -1 • The initial rate of the reaction is 5.3 mol·L¯¹·s¯¹. . If the reaction is run at constant pressure, 132. kJ/mol of heat are absorbed. • The constant pressure molar heat capacity C = 2.97 J'mol K¹. Yes. Using these facts, can you calculate K at 16. °C? x10 O No. If you said yes, then enter your answer at right. Round it to 2 significant digits. If you said no, can you at least decide whether Kat 16. °C will be bigger or smaller than K at -8.64 °C? C Yes, and K will be bigger. Yes, and K will be smaller. No.
typing clear urjent i will give 5 upvotes
The cost of materials for product A are as follows. Material W: $2,250 Material X: $3,000 Material Y: $3,600 Material Z: $150 If the material proportions were displayed on a pie chart, how many degrees would material Y represent? A 90 degrees B 120 degrees C 144 degrees D 204 degrees
typing pls
A saturated solution contains 1.80g KCIO3 in 25.0mL water at 20.0 degree celcius. Determine the solubility in units of grams solute/100g H2O and in units of molarity.
Suppose that Motorola uses the normal distribution to determine the probability of defects and the number of defects in a particular production process. Assume that the production process manufactures items with a mean weight of 10 ounces. Calculate the probability of a defect and the suspected number of defects for a 1,000-unit production run in the following situations. a. The process standard deviation is 0.15, and the process control is set at plus or minus one standard deviation. Units with weights less than 9.85 or greater than 10.15 ounces will be classified as defects. b. Through process design improvements, the process standard deviation can be reduced to 0.05. Assume that the process control remains the same, with weights less than 9.85 or greater than 10.15 ounces being classified as defects. c. What is the advantage of reducing process variation, thereby causing process control limits to be at a greater number of standard deviations from the mean?