A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in the figure below. Axial loads are applied at the positions indicated. If P = 3000 N and the cross sectional area of the rod is 325 mm2, determine the stress in each section, and total deformation of the road. E for steel is 200000 MPa, E for aluminum is 70000 MPa, E for bronze is 100000 MPa 1 3 Steel Bronze 4P Aluminum 2 500 mm 750 mm 625 mm MATHalino.com

A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in the figure below. Axial loads are applied at the positions indicated. If P = 3000 N and the cross sectional area of the rod is 325 mm2, determine the stress in each section, and total deformation of the road. E for steel is 200000 MPa, E for aluminum is 70000 MPa, E for bronze is 100000 MPa 1 3 Steel Bronze 4P Aluminum 2 500 mm 750 mm 625 mm MATHalino.com

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The wood beam has a cross section shown in figure. Determine the magnitude and location of the maximum tensile and compressive stress acting on the beam.
Part 2 * Your answer is incorrect. The z-component of momemt M will cause compression at A and B, and tension at C and D. The y-component of moment M will cause compression at A and D, and tension at B and C. The maximum tensile bending stress will occur at point C. Calculate the magnitude of the largest bending moment that can be applied so that the stress at corner C does not exceed 205 MPa. Answer: M- eTextbook and Media Save for Later Part 3 8.31E1 Answer: M-i The z-component of moment M will cause compression at A and B, and tension at C and D. The y-component of moment M will cause compression at A and D, and tension at B and C. The maximum compressive bending stress will occur at point A. Calculate the magnitude of the largest bending moment that can be applied so that the stress at corner A does not exceed 205 MPa. eTextbook and Media Save for Later Part 4 kN-m * Your answer is incorrect. kN-m Submit Answer Determine the maximum bending moment that can be applied to this cross…
A steel cantilever beam is fabricated from two structural tees welded together, as shown in the figure. For this beam, the allowable bending stress is 150 MPa, the allowable shear stress of the steel is 100 MPa, and the allowable shear flow along the weld is 2MN/m. Determine the allowable force P that the beam can carry. (All dimensions are in mm).
A small aluminum alloy [E = 65 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 125 mm. The cross-sectional dimensions of the tee shape are b = 15 mm, d = 23 mm, and t = 9 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 460 µɛ is measured from a strain gage located at c = 9 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? P 3P Strain gage D E H b. Answer: P = i 29254 N
Description A1 m long steel rod has a cross sectional area of 100 sqm. It is Elasticity modulus is 200 000 MPa. 1. Determine deformation of steel rod. 2. Determine stiffness of steel rod. 3. Determine flexibility of steel rod.
1. The assembly has the diameters and material makeup indicated. If it fits securely between its fixed supports when the temperature is T; = 70°F, determine the average normal stress in each material when the temperature reaches T2 = 130°F. 304 Stainless steel - 2014-T6 Aluminum -C 86100 Bronze A 12 in. 8 in. D C 4 in. -4 ft- 6 ft- 3 ft
A combined section of steel and copper is subjected to a compressive load. Refer to the table below for the properties of each Steel Copper Area, A 900 mm2 1,200 mm2 Modulus of elasticity, E 200 GPa 120 GPa Allowable compressive stress 140 MPa 70 MPa If the allowable strain for both materials is 0.0005, which of the following most nearly gives the maximum load the member can carry so that this allowable strain is not exceeded? Select the correct response 162.00 kN 185.00 kN 205.00 kN 175.00 kN
A cylindrical bar of steel 9.9 mm (0.3898 in.) in diameter is to be deformed elastically by application of a force along the bar axis. Determine the force that will produce an elastic reduction of 3.0×10-3 mm (1.181 ×10-4 in.) in the diameter. For steel, values for the elastic modulus (E) and Poisson's ratio (v) are, respectively, 207 GPa and 0.30. i N
A composite beam is made of two brass [E = 120 GPa] bars bonded to two aluminum [E = 70 GPa] bars, as shown. The beam is subjected to a bending moment of 400 N-m acting about the z axis. Using a = 15 mm, b = 100 mm, c = 30 mm, and d = 65 mm, calculate (a) the maximum bending stress in the aluminum bars. (b) the maximum bending stress in the brass bars. Aluminum y Brass Aluminum b Brass C a d
If a steel column with cross-sectional area A = 1000 mm2, modulus of elasticity E 200 MPa and length of 10 m is subjected to 2 kN axial tension, compute for its axial deformation O + 100 mm O +0.1 mm O 100 mm O-1.0 m
A cylindrical specimen of some metal alloy having an elastic modulus of 101 GPa and an original cross-sectional diameter of 3.6 mm will experience only elastic deformation when a tensile load of 2430 N is applied. Calculate the maximum length of the specimen before deformation if the maximum allowable elongation is 0.41 mm. i mm
The solid rod has a diameter of 20mm. Find the following: Angle of twist at C with respect to A (in radians) Angle of twist at B with respect to A (in radians) Maximum shear stress at A (in MPa) (Shear stress at support, at a point 7mm from center. (in MPa) A-36 steel with the following properties: Modulus of Elasticity, E = 29x10^3 ksi or 200 GPa Shear Modulus/Modulus of Rigidity, G = 11.5x10^3 ksi or 79.3 GPa Poisson's Ratio, nu = 0.260 Temperature Coefficient for thermal expansion, a = 6.6x10^-6/°F or 11.7x10^-6/°C