A rod has a radius of 4m. Determine the smallest force F that must be applied along the rope in order to cause the curved rod to fail at the support A. This requires a moment of M=1400 N?m to be developed at A.

A rod has a radius of 4m. Determine the smallest force F that must be applied along the rope in order to cause the curved rod to fail at the support A. This requires a moment of M=1400 N?m to be developed at A.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The beam is subjected to a load F = 300 Nand is supported by the rope and thesmooth surfaces at A and B.a. Draw the free-body diagram of thebeam.b. What are the magnitudes of thereactions at A and B?
Determine the contact force between the smooth 90 kg ball B and the horizontal bar, and the magnitude of the pin reaction at A. Neglect the weights of the bar and the pulley.
The horizontal force F acts on the handle of the wrench (i.e Fis parallel to xy-plane). What is x-component of the moment of this force about the origin "O"? F = 19.5 N, a = 36 mm, b = 200 mm, c = 10 mm, 0 30°. of B
3. Determine the resultant of the force system in the figure. y 450N 850 N 48° 350 N --- X 55° 500N
Determine the internal normal force at point C of the beam. Give your answer in N and to 3 significant digits. 200 N/m nguni C -3 m- 400 N/m 3 m B
W A B L- The propped cantilever beam above is subjected to a linearly-varying load, as shown. El is constant. Which of the following is closest to the vertical force reaction at point A? 0.333 w-L 0.25.w L 0.50-w-L 0.10 w-L
Determine the vertical displacem ent at Joint B using Virtual Work Method. AE is constant and assume all members are pin connected at their ends. D. c60 3 m B. 4 m 4 m 15 kN 20 kN
Two blocks A and B each having a mass of 10 kg, are connected by thelinkage shown. If the coefficient of static friction at the contacting surfaces is μs = 0.25, determine the largest force P that can be applied to pin C of the linkage without causing the blocks to move. Neglect the weight of the links.
plz solve it in slope deflection !! Determine the reactions at the supports. Assume A is fixed connected. E is constant SAN/m LAn-1250 (10') mm* 3 m 20 kN Inc 625 (10) mm
400 N/m Mc 600 N B 4 m C 1.5 m -1.5 m- Q5- The Figure shows a frame that is pin-supported at A and C and has an internal pin at B. The frame is subjected to concentrated force = 600 N, uniformly distributed load = 400 N/m and a couple moment Mc = 500 N.m Determine following: (a) The components of the internal force at pin B are: Bx .. kN By kN (b) The Force Reactions at the supports are: Ax- kN Ay kN Cx• k N Cy. k N
H.W2: Find the stability and determinacy of frame below ١٢ / ١٤ ...
0.3 m mathalino.com B 0.3 m Figure P-226 Given that F=100OKn and P=1434. Determine the following: f es E and D -II D C.VIO d. Moment at the Tail of Force P e. Moment at the Head of Force F f. Moment at the Head of Force P C. mathalino,com F P.