A river 80 meters wide, with a depth d at a distance x measured from one of its banks is given by the following table. x0| 10 20 30 40 50 60 70 80 d 4 7 9 12 15 14 3 By Simpson's rule, find the cross-sectional area of the river.

A river 80 meters wide, with a depth d at a distance x measured from one of its banks is given by the following table. x0| 10 20 30 40 50 60 70 80 d 4 7 9 12 15 14 3 By Simpson's rule, find the cross-sectional area of the river.

Name: ### 7.8 Training Questions#### 1. River Cross-Section CalculationA ri
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: ### 7.8 Training Questions#### 1. River Cross-Section CalculationA river 80 meters wide, with a depth \( d \) at a distance \( x \) measured from one of its banks, is given by the following table:| \( x \) (m) | 0 | 10 | 20 | 30 | 40 | 50 | 60 | 70

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3G 9:.. %79 Final 1st attem... F2 У - ахis Fs F4 F1 х - ахis X- axis y - axis F3 F2 F1 Figure (1) Figure (2) 250 N 36.87 D F2 60° 0.5 m 1 m o! 0.2 m 1 m 300 NE F1 1 m Figure (3) Figure (4) Q1] Answer the following questions: For figure (1): The object is subjected to two forces F1 = 25 N, and F2 = 50 N. Set x = 30°, 0 = 45° , and ß = 30°. 1- What is the magnitude of the resultant of these two forces? a) 39.4 N b) 80.1N c) 41.6 N d) 69.8 N e) 71.4 N f) 46.1 N g) None of them 2 - What is the direction of the resultant force measured counterclockwise from the positive x-axis? а) 14.30 b) 392.6° c) 9.2° d) 322.9° e) 6.8° f) 344.2° g) None of them For figure (2): The arm in is subjected to five forces as follows: F1 = 135 N, F2 = 98 N, F3 = 210 N, F4 = 56 N. If the y – direction resultant force is 144 N, and x = 40°, 0 = 50°, B = 70°: 3 – What is the magnitude of the force F5? a) 318.4 N b) 99.1N c) 151.6 N d) 36.5 N e) 111.2 N f) 18.8 N g) None of them 4 - What is the magnitude of the…
Please make the exact graph with the lines in the same spot and the orange and blue circles at the same spot as well.
Q3/ For the figure below: * a) The total area is: 00 000 О 0 0 0 65 67 O 76 99 63 :Q3/b) Find the value of X-bar * 86 -2.331 -1.478 0 2.134 1.45 -3.657 :Q3/C) Find the value of Y-bar* 3.875 4.88 0 2.442 4.889 6" 2 6" 1"
Note:- • Do not provide handwritten solution. Maintain accuracy and quality in your answer. Take care of plagiarism. • Answer completely. • You will get up vote for sure.
Can you show why the answer is this? Your answers are close, but why B to D member is zero how?
Check the correct statements regarding the picture. * ALT HDG MDA 310 260 240 10 220 10 200 2150 ANH 1024 ITLE 109.10 It says the aircraft is below the glide slope It is a picture of the navigational display It says the aircraft is perfectly aligned with the center of the runway It says the aircraft is to the right of the runway and not centered 10 o o 3000 。>025- - FD 2 230 >020- 20 80 07
6 x 2/ Given in the design of the following movable grid system: field dimensions (360m x 1080m), soil mixture alluvial, effective depth of root zone (80 cm), German consumption (8mm / day), sprinklers (Jism and 9m), average Wind speed (2m / sec), water holding capacity (1.7mm / cm), moisture depletion rate (50%), base infiltration rate (10.2mm / hr), note that the irrigation efficiency is (659). The main pipe passes outside the field. The spray tube is made of Aluminum material discharge coefficient (0.967 = c) required:. 1. Net irrigation depth 2- Irrigation interval 3- Total irrigation depth 4- Irrigation rate b) Number of spray tubes needed for the field c) Sprinkler drainage, spray diameter, pressure charge rate d Diameter of spray pop in cases: 6 1- Spray pop Hesto 2 The spray pop has a downward slope of (19). 3- The spray pop has a slope of (19). The pressure charge at the entrance and end of the spray tube for the three cases in d %3D
Make the statistical analysis for all of data given into table below using Excel program. N number =9 COUNT X 1 0.244(N) 2 0.234(N) 3 0.247(N) 4 0.231(N) 5 0.235(N) 6 0.244(N) 7 0.230(N) 8 0.233(N) 9 0.244(N) 10 0.241(N) 11 0.247(N) 12 0.231(N)
Fill in the given table for the following shaft and hole limits. Do only (a) and (h). use the metric tables in the back of your textbook. (a) (d) |() (b) 5.970 79.990 79.971 80.030 (c) 16.029 25.061 16.018 25.048 16.018 16.000 (e) 120.000 119.780 120.400 (g) 2.000 30.000 1.994 29.987 2.012 30.0062 7.978 2.002 9.985 (h) 8.000 7.991 Shaft Limits 5.940 Hole 6.030 25.021 Limits 6.000 80.000 25.000 120.180 7.963 Shaft Hole Limits Basic size Tolerance Upper Deviation Lower Deviation Fundamental Deviation IT Grade System (hole, shaft) Fit Shaft Hole Limits Basic size Tolerance Upper Deviation Lower Deviation Fundamental Deviation IT Grade System (hole, shaft) Fit
What's the mean of the following points? x = [-3 3 4 2 -1 1 4 5] Type your answer...