A rigid tank whose volume is 0.5 m°, initially containing ammonia at 20°C, 1.5 bar, is connected by a valve to a large supply line carrying ammonia at 12 bar, 200°C. The valve is opened only as long as required to fill the tank with additional ammonia, bringing the total mass of ammonia in the tank to 143.4 kg. Finally, the tank holds a two-phase liquid-vapor mixture at 20°C. Determine the heat transfer to the ammonia in the tank from the surroundings, in kJ, ignoring kinetic and potential energy effects. Qev i 181532.33 kJ

A rigid tank whose volume is 0.5 m°, initially containing ammonia at 20°C, 1.5 bar, is connected by a valve to a large supply line carrying ammonia at 12 bar, 200°C. The valve is opened only as long as required to fill the tank with additional ammonia, bringing the total mass of ammonia in the tank to 143.4 kg. Finally, the tank holds a two-phase liquid-vapor mixture at 20°C. Determine the heat transfer to the ammonia in the tank from the surroundings, in kJ, ignoring kinetic and potential energy effects. Qev i 181532.33 kJ

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I need the correct solution. Don't use chatgpt
An insulated cylinder-plunger device with a constant load contains 2 L of saturated liquid water at a temperature of 80 °C . A paddle wheel agitates the water, contributing 500 kJ to the system, while for 10 min a current of 8 A passes through a 110 V resistor placed in the water. It is correct to state: I) Information is missing to calculate the moving boundary work. II) The final state is a vapor-liquid mixture at 47.42 kPa. III) In the final state, the volume is equal to 0.781 m3/kg IV) The sum between the electric work and the work of the paddlewheel is equal to hfg
water at 40 ° C is converted into superheated steam at 250 ° C at 150 kPa. Specify: a. Initial enthalpy of water (Singh's Book Tab A 4.2) = AnswerkJ / kg. b. Enthalpy at saturated vapor pressure = AnswerkJ / kg. c. Superheated vapor enthalpy (Tab A Singh's Book 4.3) = AnswerkJ / kg. d. Total enthalpy change = AnswerkJ / kg.
A reheat cycle with two stages of reheating is executed with steam expanding initially from 25 MPa and 600 °C. The two reheater pressures are 4 MPa and 1 MPa, and the steam leaves each reheater at 600 °C. Condensation occurs at 40°C. For 1 kg/s of steam, what is QA in kW? Remember, 1. For values taken from the steam tables: Use them as is, do not round off. 2. For values obtained by interpolation and final answers obtained by solving, use FOUR (4) decimal places. 3. Use the steam tables provided
4.61 Apiston/cylinder arrangement shown in Fig. P4.61 initially contains air at 150 kPa and 400°C. The setup is allowed to cool to the ambient temperature of 20°C. a. Is the piston resting on the stops in the final state? What is the final pressure in the cylinder? b. What is the specific work done by the air during the process? Air FIGURE P4.61 1m 1m
A metal rod 0.4 m long & 0.04 m in diameter has one end at 373 K & another end at 273 K. Calculate the total amount of heat conducted in 1 minute. (Given K = 385 J/m s °C)
13
Water vapors at 40 bar enters a pipe fitting (adapter) with a velocity of 169 m/s and exits thefitting at 10 bar and 572°F. If the temperature at the inlet is 1004°F., calculate the exit velocity.The system is assumed to be at steady state.
Steam, initially at 5 MPa, 280°C undergoes a polytropic process in a piston–cylinder assembly to a final pressure of 20 MPa. If the polytropic constant, n = 1.4, calculate the non-flow work in kJ/kg.
Calculate the energy requirement to raise the temperature of 1 kg of water from 60 ° C of water to 90 ° C using the following approach; a. Average specific heat usage (Tab A Singh's Book. 4.1) = kJ b. The enthalpy change in the water - vapor saturation table (Tab A Singh's Book. 4.2) = kJ
Refrigerant 134a at p1 = 30 lb/in?, T1 = 40°F enters a compressor operating at steady state with a mass flow rate of 400 lb/h and exits as saturated vapor at p2 = 160 lb;/in?. Heat transfer occurs from the compressor to its surroundings, which are at To = 40°F. Changes in kinetic and potential energy can be ignored. The power input to the compressor is 4 hp. Determine the heat transfer rate for the compressor, in Btu/hr, and the entropy production rate for the compressor, in Btu/hr-°R.
Refrigerant 134a at p1 = 30 lbş/in?, T1 = 40°F enters a compressor operating at steady state with a mass flow rate of 250 lb/h and exits as saturated vapor at p2 = 160 lbę/in?. Heat transfer occurs from the compressor to its surroundings, which are at To = 40°F. Changes in kinetic and potential energy can be ignored. The power input to the compressor is 2.5 hp. Determine the heat transfer rate for the compressor, in Btu/hr, and the entropy production rate for the compressor, in Btu/hr-°R.