A rigid tank whose volume is 0.5 m³, initially containing ammonia at 20°C, 1.5 bar, is connected by a valve to a large supply carrying ammonia at 12 bar, 130°C. The valve is opened only as long as required to fill the tank with additional ammonia, bringing the total mass of ammonia in the tank to 136.7 kg. Finally, the tank holds a two-phase liquid-vapor mixture at 20°C. Determine the heat transfer to the ammonia in the tank from the surroundings, in kJ, ignoring kinetic and potential energy effects. Qw = ! kJ

A rigid tank whose volume is 0.5 m³, initially containing ammonia at 20°C, 1.5 bar, is connected by a valve to a large supply carrying ammonia at 12 bar, 130°C. The valve is opened only as long as required to fill the tank with additional ammonia, bringing the total mass of ammonia in the tank to 136.7 kg. Finally, the tank holds a two-phase liquid-vapor mixture at 20°C. Determine the heat transfer to the ammonia in the tank from the surroundings, in kJ, ignoring kinetic and potential energy effects. Qw = ! kJ

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider a turbine operating at steady-state with the operating conditions shown in the figure. Superheated water vapor enters the turbine with a mass flow rate of m = 5 and superheated water vapor exits at p2 and T2. Ignoring stray heat transfer and kinetic and potential effects: a. Calculate the net power of the turbine, Wr, in kW b. Calculate the entropy produced in kW/K All state properties needed to solve are provided below: State T (°C) p (bar) h (kJ/kg) s (kJ/kg-K) (1 1 240 10 2920.4 6.8817 Wr 2 160 3 2782.3 7.1276 P1 = 10 bar T = 240 °C = 3 bar (2) P2 T2 = 160 °C
13
13
Argon (molar mass 40 kg/kmol) compresses reversibly in an adiabatic system from 5 bar, 25 0C to a volume of 0.2 m3. If the initial volume occupied was 0.9 m3, calculate the work input in MJ to 3 decimal places. Assume nitrogen to be a perfect gas and take cv = 0.3122 k J / k g K.
Water vapors at 40 bar enters a pipe fitting (adapter) with a velocity of 169 m/s and exits thefitting at 10 bar and 572°F. If the temperature at the inlet is 1004°F., calculate the exit velocity.The system is assumed to be at steady state.
Steam, initially at 5 MPa, 280°C undergoes a polytropic process in a piston–cylinder assembly to a final pressure of 20 MPa. If the polytropic constant, n = 1.4, calculate the non-flow work in kJ/kg.
Calculate the energy requirement to raise the temperature of 1 kg of water from 60 ° C of water to 90 ° C using the following approach; a. Average specific heat usage (Tab A Singh's Book. 4.1) = kJ b. The enthalpy change in the water - vapor saturation table (Tab A Singh's Book. 4.2) = kJ
Refrigerant 134a at p1 = 30 lb/in?, T1 = 40°F enters a compressor operating at steady state with a mass flow rate of 400 lb/h and exits as saturated vapor at p2 = 160 lb;/in?. Heat transfer occurs from the compressor to its surroundings, which are at To = 40°F. Changes in kinetic and potential energy can be ignored. The power input to the compressor is 4 hp. Determine the heat transfer rate for the compressor, in Btu/hr, and the entropy production rate for the compressor, in Btu/hr-°R.
Carbon dioxide (CO₂) fills a closed, rigid tank fitted with a paddle wheel, initially at 80°F, 50 lb/in², and a volume of 1.6 ft³. The gas is stirred until its temperature is 500°F. During this process heat transfer from the gas to its surroundings occurs in an amount 2.6 Btu. Assume ideal gas behavior, but do not assume constant specific heats. Kinetic and potential energy effects can be ignored. Determine the mass of the carbon dioxide, in lb, and the work, in Btu.
Two vessels A and B of different sizes are connected by a pipe with a valve. Vessel A contains 134L of air at 2,639.66 kPa, 87.38°C. Vessel B, of unknown volume, contains air at 69.36 kPa, 6.33°C. The valve is opened and, when the properties have been determined, it is found that Pm = 1,041.50 kPa, tm = 46.30°C. What is the volume of vessel B?
Five kilograms of a two-phase liquid-vapor mixture of water initially at 300\deg C and x1 = 0.5 is heated from the initial state to a saturated vapor state while the volume remains constant. The process is brought about by heat transfer from a thermal reservoir at 380\deg C. The temperature of the water at the location where the heat transfer occurs is 380\deg C.Let To = 300 K, Po = 1 bar, and ignore the effects of motion and gravity.
Question 21 A rigid tank whose volume is 0.5 m, initially containing ammonia at 20°C, 1.5 bar, is connected by a valve to a large supply line carrying ammonia at 12 bar, 200°C. The valve is opened only as long as required to fill the tank with additional ammonia, bringing the total mass of ammonia in the tank to 136.7 kg. Finally, the tank holds a two-phase liquid-vapor mixture at 20°C. Determine the heat transfer to the ammonia in the tank from the surroundings, in kJ, ignoring kinetic and potential energy effects. Qcv > = kJ