A rigid, insulated tank that is initially evacuated is connected through a valve to a supply line that carries steam at 4 MPa. Now the valve is opened, and steam is allowed to flow into the tank until the pressure reaches 4 MPa, at which point the valve is closed. If the final temperature of the steam in the tank is 550°C, determine the temperature of the steam in the supply line and the flow work per unit mass of the steam.

Q: A variable-load piston-cylinder device contains air (cp = 1.005 kJ/kgK; cv = 0.718 kJ/kgK) at 500…

A:

Q: A compressor operating with 7.7 kg/s water vapour with a compression ratio (P2/P1) equal to 3.0 is…

A:

Q: A piston-cylinder device contains 0.1 m³ of refrigerant 134a at 0.24 MPa and 40°C. Initially the…

A:

Q: Steam enters a turbine steadily at a flow rate of 1 kg/s at 7 MPa and 500 degrees and exits as…

A: Inlet conditions:Mass flow rate (ṁ) = 1 kg/sInlet pressure (P1) = 7 MPaInlet temperature (T1) =…

Q: Insulated container X and uninsulated container Y are connected with a valve both initially…

A: We have to determine temperatures at container Y

Q: Refrigerant-134a enters a compressor at 180 kPa as a saturated vapor with a flow rate of 0.35 m³/min…

A:

Q: piston cylinder assembly initially contains 25g of saturated water vapor at 600kpa pressure. Then,…

A:

Q: Water is heated in a boiler. The inlet water enters as a saturated liquid at 5000 kPa and exits at…

A:

Q: A 0.3 m³ rigid tank contains refrigerant 134a at 650 kPa. Initially, 45% of the volume is occupied…

A:

Q: Sleäm at a pressure of Ра and lemperaure Is passed al a constant rate into a desuperheater unit. The…

A: Solution: State properties at state 1   (Before massing through desuperheater)…

Q: In the first case, two pipes are connected to a tank containing liquid water at 45kg and 45℃. Liquid…

A:

Q: A rigid, insulated tank that is initially evacuated is connected through a valve to a supply line…

A: Linear interpolation is a method of curve fitting that uses linear polynomials to create new data…

Q: A rigid tank of volume 0.018 m' is connected through a closed valve to a vertical cylinder fitted…

A: Given: The volume of the air inside the tank, V1 = 0.018 m^3 The pressure of air inside the tank, P1…

Q: A rigid tank initially contains 0.9 kg of water. Then it is filled more with steam from a supply…

A: Given: Mass of water mw=0.9kg Final mass of the tank m=2kg Pressure of steam supplied P1=1.5MPa…

Q: A piston cylinder contains 1.25 kg water at 25°C with a constant load on the piston such that the…

A: Given data:-Initial mass,m1=1.25kgInitial temperature, T1=25°C=298KPressure, P=300kPaFinal mass,…

Q: A 12 ft^3 rigid tank initially contains saturated water vapor at 250 F. The tank is connected by a…

A:

Q: A 0.25 m^3 rigid tank contains refrigerant-134a at 0.8 MPa and 100 percent quality. The tank is…

A:

Q: An 22 m3 rigid tank initially contains Argon gas at 152 kPa and 28 oC. The tank is connected by a…

A: (a) To find: The final temperature of the tank in Kelvin. Given: The initial volume of the tank is…

Q: Refrigerant-134a enters the compressor of a refrigeration system as saturated vapor at 0.14 MPa and…

A: The refrigerant enters the compressor as saturated vapor at The refrigerant leaves the compressor as…

Q: What is the heat transfer out of the tank in units of Btu? Select the answer that is closest to the…

A:

Q: A work producing device of the piston-cylinder system at the beginning contains 1.5 kg of…

A: Write the given information. Write the expression of mass at state 2.

Q: In an open system, 500 kg/h of air is being compressed from 100 kPa at  280 K to 600 kPa and 400 K.…

A:

Q: Air leaves a compressor at 1.5 MPa and 90°C with a mass flow rate of 150 kg/min. Determine the…

A: Given, At the exit of the compressor,Pressure, P2=1.5MPaTemperature, T2=90°C=363KMass flow rate,…

Q: The pressure of saturated water vapor in an insulated tank with a volume of 5.7 m3 is 350 kPa. The…

A:

Q: A rigid tank of 0.22-m'volume initially contains saturated vapor refrigerant-134a at 1.2 MPa. The…

A:

Q: An insulated piston cylinder assembly initially contains 5 L of saturated liquid water at a constant…

A: The energy balance for this closed system could be defined as the following.

Q: A rigid, well-insulated tank is initially empty. The tank is kept connected by means of a valve to a…

A:

Q: Refrigerant-134a is throttled from the saturated liquid state at 22°C to a temperature of -10°C.…

A:

Q: An expansion valve is a part of an adiabatic rigid steam boiler. Steam's initial pressure and…

A:

Q: Steam enters the condenser of steam power plant at 20 kPaa and quality of 95% with a mass flow rate…

A: Answer: (a) The heat rejected by the condenser is 12446.58333 kW. (b) The mass flow rate of the…

Q: Consider a rigid container that is initially empty, connected by a valve to a feed line of water at…

A:

Q: I want to know how this four pressures and enthalpies are selcected

A: Since in solution we have given Four pressure values: and

Q: The refrigerant R-134a enters the compressor of a refrigeration machine at a pressure of 140kPa and…

A:

Q: he refrigerant R-134a enters the compressor of a refrigeration machine at a pressure of 140kPa and a…

A:

Q: Air expands in a gas turbine from 590kPa to 102kPa. The expansion obeys the law pv1.27 = C the…

A:

Work and Heat Transfer

It is generally related to thermal engineering which tells about the use, creation, conversion and transfer of heat energy between the systems. It is also considered that to transfer heat from one source to another, transfer of masses is also required. There are various mechanisms by which, transfer of heat takes place i.e. thermal conduction, convection, radiation or by change of phase. All these mechanisms have their own specific features which sometimes occur simultaneously within the same system.