Given :Steel: A = 600mm2 ; E = 200 GPaBronze : A = 900mm2 ; E = 83 GPaShow the complete solution and FBD A rigid block weighing 176.4 kN isattached as sho un on the figure.If the block is to. remain hon Zontal.olumBronzeSteelSteel1,0ma) which of the following gives ther dtio of the load carried by eachload.b.) Which of the follo wing gives theStress Of the bro nze-Śc)Which of the folowing gives flie elongationof the rods.

Answered: Image /qna-images/answer/ade86466-9c7f-4959-8567-430a6f3a76ca.jpg

A rigid block weighing 176.4 kN is attached as sho un on the figure. If the block is to remain hon Zontal. Bronze Ollom Steel Steel 1,0m a) which of the following gives the r dtio of the load carried by each load. b.) Which of the follo wing gives the Stress Of the bro nze- Śa)Which of the folowing gives flie elongation of the rods.

A rigid block weighing 176.4 kN is attached as sho un on the figure. If the block is to remain hon Zontal. Bronze Ollom Steel Steel 1,0m a) which of the following gives the r dtio of the load carried by each load. b.) Which of the follo wing gives the Stress Of the bro nze- Śa)Which of the folowing gives flie elongation of the rods.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A combined section of steel and copper is subjected to a compressive load. Refer to the table below for the properties of each Steel Copper Area, A 900 mm2 1,200 mm2 Modulus of elasticity, E 200 GPa 120 GPa Allowable compressive stress 140 MPa 70 MPa If the allowable strain for both materials is 0.0005, which of the following most nearly gives the maximum load the member can carry so that this allowable strain is not exceeded? Select the correct response 162.00 kN 185.00 kN 205.00 kN 175.00 kN
Getting measurements from Figure , determine approximate values of the following items for steel with different carbon contents. Use one system of units only as specified by the instructor.a. Yield stressb. Ultimate strengthc. Strain at failured. Effect on modulus of elasticitye. Approximate toughness. Curves may be approximated with a series of straight lines.f. Comment on the effect of increasing carbon content on items a through e above.
If the modular ratio is equal to 7, and the Modulus of Elasticity of the Steel is 200,000 MPa. What is the value of fc'?
Note:please help us in this sample given problem thank you
Please help I need it in 30 minutes
Find the value of p
Determine the ductility of the following steel samples that undergo tensile strength test. All dimensions in millimeter.
At a temperature of 29.8 °C a 0.4-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 133.3°C, determine the change in length of the steel rod if L = 312.45 mm and M=201 mm. Round off the final answer to four decimal places. d - L M - B Aluminum A = 2000 mm² E = 75 GPa a = 23 x 10-6/°C Stainless steel A = 800 mm² E = 190 GPa α = 17.3 x 10-6/°C
Please show solutions on how to get the 0.75 value. The circle green in the figure. Civil engineering- steel design
Date: Course: Time: Pind the vertical movement os is 120 KN Stsel Aluminum 3 m Im B P=120 kat Aluminum A = 900 mm² E = 70 GN m² steel A= 600 mm E 200 GNM² %3D
Pencil leads are made up mostly of the following elements. a. graphiteb. leadc. clayd. none of the preceding
I need the answer as soon as possible