A rigid beam is hinged at one end and supported on linear elastic springs (both having a stiffness of'k') at points '1' and '2', and an inclined load acts at '2', as shown.HingeFixedk459B45°VITOUMY.Fixed12 P2If the load P equals 100 kN, which of the following options represents forces R₁ and R₂ in thesprings at points '1' and '2'?

Given- Load P=100 kN, It is required to find spring force R1 & R2.

A rigid beam is hinged at one end and supported on linear elastic springs (both having a stiffness of 'k') at points '1' and '2', and an inclined load acts at '2', as shown. Hinge 2 P Fixed 45° * 45° Fixed 2 If the load P equals 100 kN, which of the following options represents forces R₁ and R₂ in the

A rigid beam is hinged at one end and supported on linear elastic springs (both having a stiffness of 'k') at points '1' and '2', and an inclined load acts at '2', as shown. Hinge 2 P Fixed 45° * 45° Fixed 2 If the load P equals 100 kN, which of the following options represents forces R₁ and R₂ in the

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The rigid beam shown is supported by a pin at A and two steel rods each of diameter 16 mm. If P = 30 kN, determine the tensile forces PBE & PCF in rods BE and CF, respectively. For steel, E = 200 GPa. F 2.0 m E P = 30 kN 2.5 m D -3 m- -3 m-
The bridge is pinned at A and has a roller at G. A downward load of 12.5 lb is applied at point C, and a downward load of 25 lb is applied at E. The support reactions at the pin and roller are shown on the image. Find the stress in members making up the bridge using either the method of joints or method of sections.
Q4/ The rigid beam is supported by a pin at A and two steel wires BD and CE. Each rod has a diameter of d. If the load P on the beam causes the end C to be displaced h downward, determine the normal strain developed in wires CE and BD and the applied load P. Assume E seel = 200 Gpa and a= 1.5 m, b= Im, d=30 mm, h= 8 mm 2a
The signboard truss is designed to support a horizontal wind load of 530 lb. If the resultant of this load passes through point C, calculate the forces in members BG and BF. The forces are positive if in tension, negative if in compression. 530 lb Answers: BG= BF= i i 4' C B 4' G +2¹ 3' - w w. F 3' lb lb
If the allowable bearing stress for the material under the supports at A and B is Ob = 780 psi, determine the maximum load Pmax that can be applied to the beam. The bearing plates each have square cross sections of 5 in. by 5 in. The reactions at the supports are vertical. Assume w = 600 lb/ft, a = 12 ft, and b = 6 ft. Answer: Pmax= i W a B b lb P
Determine the reactions for the beam shown if the vertical deflection at support B is zero. 3.0 kip/ft O B 16' 8' SIMPLE BEAM: CONCENTRATED LOAD AT ANY POINT SIMPLE BEAM: UNIFORMLY DISTRIBUTED LOAD Pb R = V, (max when a b) R V, . Pab w V M max (at point of load). M max (at center) Pbx Shear M, (when x b) = Pab(a + 2bN3a(a + 2b) M max Amax (at center), 27EI Pah2 384EI M max Moment A, (at point of load) 3EII WX (3 – 21r2 + x³) Pbx (2 - b2 - x) 4, 24EI 4, (when x
Q4/ The rigid beam is supported by a pin at A and two steel wires BD and CE. Each rod has a diameter of d. If the load P on the beam causes the end C to be displaced h downward, determine the normal strain developed in wires CE and BD and the applied load P. Assume E steel = 200 Gpa and a= 1.5 m, b= 1lm, d=30 mm, h= 8 mm 2а b a - a
Problem 5. The frame shown is hinged to rigid supports at A and E. Find the components of the hinge forces A and E and the forces in members BC and BD. E A 2m 2.5m 12 kN D 2m 1.5m B 2m
Draw the shear force diagram and the bending moment diagram of the bridge girder shown below. FAC = 84.1K (T) Fec 84.1K (T) FCD=64.7 K (c) 5 ft A 12 ft- 80 k D C 12 ft B
For the truss shown below, applied loads are PB = 73 kN, PC = 36 kN and PD = 15 kN. Using the sign convention 'tension positive', select the correct answer for the axial force in member GH in kN: К F AR G В Рв 4@3m=12m O 1. The axial force in member GH is -60 kN. O2. The axial force in member GH is -78 kN. O 3. The axial force in member GH is -67.1 kN. Н Pc J D Ро K E 4m ?
The frame below is loaded as shown, with a pin support at C and a roller pin support at E. Member FADE has a length of 16 ft and member BDG has a length of 7 ft. triangle ABD is an equilateral triangle. When P = 50 lb, find the forces acting on member ABC at points A, B and C. (point H is not relevant to this problem). F ↑ 4 ft 3 ft A B C H Solve the problem and answer the questions that follow. P G E
Q4/ The rigid beam is supported by a pin at A and two steel wires BD and CE. Each rod has a diameter of d. If the load P on the beam causes the end C to be displaced h downward, determine the normal strain developed in wires CE and BD and the applied load P. Assume E steel = 200 Gpa and a=lm, b= 1.75m, d=50 mm, h= 6mm E D 2a b