The frame below is loaded as shown, with a pin support at C and a roller pin support at E. Member FADE has a length of 16 ft and member BDG has a length of 7 ft. triangle ABD is an equilateral triangle. When P = 50 lb, find the forces acting on member ABC at points A, B and C. (point H is not relevant to this problem). F ↑ 4 ft 3ft A B C H Solve the problem and answer the questions that follow. P G E

The frame below is loaded as shown, with a pin support at C and a roller pin support at E. Member FADE has a length of 16 ft and member BDG has a length of 7 ft. triangle ABD is an equilateral triangle. When P = 50 lb, find the forces acting on member ABC at points A, B and C. (point H is not relevant to this problem). F ↑ 4 ft 3ft A B C H Solve the problem and answer the questions that follow. P G E

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate the force in member BG using a freebody diagram of the rigid member ABC. The force is positive if in tension, negative if in compression. E 14' р 14' G 14' 14' 14' 630 lb Answer: BG = i Ib
Q4/ The rigid beam is supported by a pin at A and two steel wires BD and CE. Each rod has a diameter of d. If the load P on the beam causes the end C to be displaced h downward, determine the normal strain developed in wires CE and BD and the applied load P. Assume E steel = 200 Gpa and a= 1.5 m, b= 1lm, d=30 mm, h= 8 mm 2а b a - a
Static please give the correct answer. Thank you
The members of the truss are assumed to be pinconnected. If member CB is an A-36 steel rod of 40 mmdiameter, determine the maximum load P that can besupported by the truss without causing the member tobuckle. For A36 steel E=200 GPa and σY = 250 Mpa
For the frame below, find the internal forces in element BD. The applied loads are each L = 500 pounds. L L 10" 15" 30° 30 10" D A E 20" B.
Determine the force in member BF. The force is positive if in tension, negative if in compression. B 26° 12 G 7.0 kips 3.5 kips 4.0+ 4.0- -4.0'- Answer: BF - 3.15 kips
For the frame and loading shown, determine (a)the reaction at D, (b) the force in member BE.
Given a = 20º and ß = 60º. Determine the moment (1) at A (2) at B F,= 250N F2= 300w A 2m* 4m 3 F3=500N
5
Q4/ The rigid beam is supported by a pin at A and two steel wires BD and CE. Each rod has a diameter of d. If the load P on the beam causes the end C to be displaced h downward, determine the normal strain developed in wires CE and BD and the applied load P. Assume E steel = 200 Gpa and a=lm, b= 1.75m, d=50 mm, h= 6mm E D 2a b
Consider the frame as shown in the figure. A moment of 80 kN-m acts at the joint O, given that the support at B fails at any moment greater than 18 kN-m. Then support B is (a) Unsafe (c) Just Safe A L, EI D L, EI D 80 kNm B L, EI L, EI C (b) Safe (d) Cannot be determined
*4-88. If the allowable normal stress for the bar is = 120 MPa, determine the maximum axial force P that can be applied to the bar. σ O allow PA 40 mm 5 mm 20 mm r = 10 mm 20 mm Probs. 4-87/88 P