A rigid beam BC is suspended by rods AB and CD as shown in the figure. Rod AB is made from aluminum while rod CD is made from steel. Determine the location/ placement of the 75kN concentrated load within the beam BC such that the rigid beam BC will remain horizontal after deflection. Determine the axial deformation of rods AB and CD.

Q: The solid compound shaft made of three different materials carries the two torques as shown. (a)…

A:

Q: In the figure below, at section n-n (x = 4m from point A) determine shearing stress at a on the…

A:

Q: Problem 2: For the shown beam, 40 N 150 N 250 N knowing that distance d = 1.0 m: a. Calculate the…

A: Given:- A beam is loaded with point loads The magnitude of the point load 1 (P1) = 40 N  The…

Q: In the truss shown, A =1000 mm², E = 200 GPa and the coefficient of thermal expansion is 12 x10…

A:

Q: The cantilever T-beam is loaded as shown in the figure. 80 mm 40 kN/m NA 120 mm 20 m INa = 30x106 mm…

A:

Q: The beam shown in Fig. is made from two boards. Draw the shear stress at (A,B,C,D) to hold the…

A: A simply supported beam subjected to external loading is subjected to shear. Shear force induces…

Q: PROBLEM 2: Find the resultant of the applied forces on the beam that is loaded as shown.

A: The given beam has point load , moment , uniformmly distributed load. Rectangular load on beam…

Q: C Question 3-A) vertical displacement of the point (& A) to find. Write your result in mm. Question…

A: Finding reaction and accordingly the displacement are found for rigid body

Q: 55 KN 200 KN 30⁰ 30 kN 40⁰ 20⁰ 100 kN u X

A:

Q: A prismatic bar is fastened between two rigid walls A and Band subjected to loads as shown in…

A: RA + RB =  13.6 + 22.7  RA + RB =   36.3 kNn

Q: A telescope with tripod weighs 25 pounds and has geometry as shown in the figure and parameter…

A:

Q: Particle A lies on the x-y plane and is acted on by the three forces shown. Find the resultant of…

A:

Q: The stress on a structure is as follows. The EI of the ?-shaped part of the structural section is…

A:

Q: the middle of the AB AB rigid beamWhen w = 105 kN /m is

A:

Q: In the beam given below, it is subjected to a load of L= 4 m and a uniformly distributed load q=15…

A:

Q: The steel plate shown below is put in into a rigid chamber, such that spacings of size s 0.00188 m.…

A:

Q: If the Force of members AB, AC, and BC is 7kN, 6.06kN, and 0.37kN, what is the magnitude of the…

A: Given Data  Force in member  FAB = 7 KN  FAC = 6.06 KN  FBC = 0.37 KN  Find force in member CD and…

Q: 200 mm If the beam is subjected to a bending moment of M=50KN, determine the maximum bending stress…

A: Using formula to find bending stress

Q: Figure P24.25a shows a uniform beam subject to a linearly increasing distributed load. The equation…

A: Given Parameters: L = 600 cm E = 50000kn/cm2 I = 30000 w0 = 2.5 kn/cm

Q: eam shown.

A: since the simply supported beam is carrying udl, the maximum moment occurs at the mid span of…

Q: 2.- The bar in the figure is loaded by the forces shown at B and C. Determine the reactions at A and…

A:

Q: In the set of beams as shown in the figure below, the reactive force at support Bis kN. 50 kN 20 kN…

A:

Q: Ql:- The coplanar force system shown in Figure below is subjected to a couple moment (M) and three…

A: Coplanar forces: In the coplanar force system, all the forces acting in one plane of action. They…

Q: A prismatic beam P-Q-R of flexural rigidity El = 1x104 kNm2 is subjected to a moment of 180 kNm at Q…

A:

Q: The maximum bending moment induced in the beam loaded as shown in figure is KM, then the value of Ik…

A:

Q: Q.12 An aluminium bar (E = 70 GPa, µμ = 0.33) of diameter 20 mm is stretched by an axial force P…

A: Given - An aluminium bar, E = 70 GPa,  μ = 0.33  Diameter = 20 mm Due to an axial force diameter…

Q: A steel column of length 4.75 m forms part of a support structure and is subjected to an axial…

A: i)Slenderness ratio λ: It is defined as the ratio between effective length minimum radius of…

Q: A Given the FLEXURAL beam shown=6000 RIGIDITY of the KN.m^2, find the :deflection at the roller…

A: Roller support is a support condition in which vertical movement is restrained while the rotation…

Q: Determine the magnitudes of the reactions at A and B for the beam subjected to the uniform load…

A: Given beam:-

Q: L AB beam. According to this; To AB rigid beamWhen a distributed load of magnitude w = 105 kN / m is…

A: Reactions of points are calculated and rigid body displacement are found

Q: Determine the reactions for the following structure by using Method of Consistent Deformation.…

A:

Q: (a) (c) Question 7 The vertical deflection of node C for the truss shown in figure is 2 PL AE PL AE…

A:

Q: Q1) A Section of railway track consists of a steel bar of length 15m and cross-sectional area…

A:

Q: 3 m

A:

Q: In the set of beams shown below, the reactive force at support A is: 60 N 40 N 2 m 1.75 m 60 N D A C…

A:

Q: We15 KN/m P-30

A:

Q: (a) Calculate the magnitude of force G. given that the maximum normal stress in each member should…

A:

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.