Sy Step-by-Step Calculator - Syn x b Change in length of strut DC Xb The displacements at points I xA WebAssign - ENGR 2331 Su2 x->A webassign.net/web/Student/Assignment-Responses/last?dep=26956849#Q6W 24 Statically Indeterminate S xE AppsM GmailD YouTubeMapsO Reading listA rigid bar of weight W= 810 N hangs from three equally spaced vertical wires (length L- 150 mm, spacing a= S0 mm): two of steel and one of aluminum. The wires also support a load Pacting on the bar. The diameter of the steel wires is d-2 mm, and the diameter of thewire is d,=4 mm. Assume E, - 210 GPa and E, = 70 GPa.Rigid barof weight W(a)L.Rigid barof weight W(b)(a) What load P (in N) can be supported at the midpoint of the bar (x = a) if the allowable stress in the steel wires is 200 MPa and in the aluminum wire is 65 MPa? (Se figure part (a).)(b) What is P (in N) if the load is positioned at x = a/2?N(c) Repeat part (b) if the second and third wires are switched as shown in the figure part (b). (Enter your answer in units of N.)6:20 PM(?73°F Partly sunny a O d07/10/2021P Type here to searchhp

FBD of rigid bar Area of Aluminium wireAA=π4dA2=π442=12.5664mm2Area of steel wire…

A rigid bar of weight W- 810 N hangs frem three equally spaced vertical wires (length L-150 mm, spacing a 50 mm): twe of steel and one of aluminum. The wires also support a load Pacting on the bar. The diameter of the steel wires is d-2 mm, and the diame wire is d,-4 mm. Assume E,- 210 GPa and E,- 70 GPa. Rigid bar of weight W (a)

A rigid bar of weight W- 810 N hangs frem three equally spaced vertical wires (length L-150 mm, spacing a 50 mm): twe of steel and one of aluminum. The wires also support a load Pacting on the bar. The diameter of the steel wires is d-2 mm, and the diame wire is d,-4 mm. Assume E,- 210 GPa and E,- 70 GPa. Rigid bar of weight W (a)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The rigid element ABCD is supported by a pin at C and two rods at A and D as shown in the figure. A load P is applied at B.[L₁ = 600 mm, A₁ = 67 mm², E₁ = 200 GPa, L₂ = 180 mm, A₂ = 647 mm², E₂ = 100 GPa, a = 600 mm, b = 350 mm, c = 300 mm, and P = 64 kN] T a. Determine the axial force and normal stress in in rod 1 and rod 2 b. Determine the displacement at point A and D
Q1 (а) A hollow circular post ABC as shown in Figure Q1 (a) supports a load P, = 65B5 N acting at the top. P2 is applied around the cap plate at B. The outer diameters and thicknesses of the upper and lower parts of the post are dAB = 30 mm, tu =1A mm, dzc = 50 mm, and t3c =9 mm , respectively. A=1 B=0 (i) Calculate the normal stress o AR on the upper part of the post. (ii) If it is desired that the lower part of the post have the same compressive stress as the upper part, what should be the magnitude of the load P,? (111) If Pi remains at 65B5 N and P2 is now set at 10050 N, what is the new thickness of BC that will result in the same compressive stress in both parts?
A steel rod having a cross-sectional area of 300 mm2 and a length of 150 m is suspended vertically from one end. It supports a load of 20 kN at the lower end, if E = 200 GPa, find the O ?total elongation of the rod
Find the forces in CE and DE of the truss shown in Figure (6) below (indicate tension or compression). Assume all joints are pinned. "tan (2+5) = 56.3² H pe 0.67 B 1m 1m C 1KN 1m 1m 1m F Figure (6) FDE = 0.4 kN (C) & FCE = 0.67 kN (T) 10% bis -75 0.75m G PNG 6-3-1+NG 3 NG= mbination of the method of joints
1. A rigid horizontal bar of negligible mass is connected to two rods as shown in the figure. If the load P = 10 kN. determine the following: (1) the vertical movement on the bronze, mm (2) the vertical movement on the steel, mm (3) the vertical movement at P. Figure Steel 2m A = 900 mm? E = 200 GPa 3m 3m www I 2m> 1m Bronze A = 1200 mm? 2m E = 83 GPa P = 10 kN ww.
A hollow compression member with circular cross section having outer diameter 2 times the inner diameter and ultimate tensile strength 650 MPa is subjected to an axial load of 50KN and F.S of 5. Find the inner diameter.
A steel bar with a uniform cross section is fixed at both ends. A load P = 2.5 kips is applied at point C. The bar has a cross-sectional area of 8 in2.Calculate the reactions at joints A and B and the displacement at joint C. Assume that the modulus of elasticity E = 29,000 ksi.
Give me right solution according to the question clearly.. Thank you
An aluminum bar having a cross-sectional area of 160 mm2 carries the axial loads at the positions shown in the figure. If Modulus of elasticity is 70 GPa, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling.
2.2-4 A steel cable with a nominal diameter of 25 mm (see Table 2-1) is used in a construction yard to lift a bridge section weighing 38 kN, as shown in the figure. The cable has an effective modulus of elastic- ity E = 140 GPa. (a) If the cable is 14 m long, how much will it stretch when the load is picked up? (b) If the cable is rated for a maximum load of 70 kN, what is the factor of safety with respect to failure of the cable? ▬▬
i need the answer quickly
I need to solve this question as soon as possible