A reinforced concrete T-beam has an effective flange width of 800mm with a slab thickness of 110mm. The effective depth is p0mm and the width of web is 320mm. The beam is reinforced with 6325 sq.mm. Of steel with fy=345 MPa. Assuming fc'=26.50 Pa alculate the service live load at midspan in addition to a total deadload of 8KN/m if the span of beam is 6m.

A reinforced concrete T-beam has an effective flange width of 800mm with a slab thickness of 110mm. The effective depth is p0mm and the width of web is 320mm. The beam is reinforced with 6325 sq.mm. Of steel with fy=345 MPa. Assuming fc'=26.50 Pa alculate the service live load at midspan in addition to a total deadload of 8KN/m if the span of beam is 6m.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Concrete designs, i need solutions in 10 minutes please. Q/a rectangular Beam has width (300mm) and effect depth (500mm). It is reinforced with 4ø25 in one row . If (fc'=21MPa) and (fy=420MPa) find the ultimate moment that the beam can carry?
Q4/ Compact the design bending strength to the reinforced concrete beam has a width b=300mm and effective depth d=525mm, fc-20, fy=300MPa. Suppose that the beam design to achieve a maximum bending according to code.
In the built-up girder shown below that has an unbraced length of 25 ft. (L-25 ft) and moment gradient factor of C,-1, determine the maximum flexural design strength. E-29000 ksi Fy-50 ksi PL 25x0.6" PL 35*0.3" PL 25x0.6"
Use F = 50 ksi and select a shape for a typical floor beam AB. Assume that the floor slab provides continuous lateral support. The maximum permissible live load deflec- tion is L/180. The service dead loads consist of a 5-inch-thick reinforced-concrete floor slab (normal weight concrete), a partition load of 20 psf, and 10 psf to account for a suspended ceiling and mechanical equipment. The service live load is 65 psf. a. Use LRFD. -4 @ 6' = 24- 30′ a. W16X31 b. W16X45 c. W16X26 d. W16X77 e. W16X57 H -H
A reinforced concrete T-beam is to be designed for tension only. The beamwidth is 250 mm. effective depth to bottom bars is 400 mm, flange thickness is 100mm, simple span is 3.6 m and beam spacing is 1.2 m on centres. If the applied designmoment is 300 kn-m, fc’ = 20.7 MPa and fy = 414 MPa. Determine the effective widthof the compression flange and the number of 28 mmφ diameter bars necessary forthe beam.
A rectangular cross section of a beam is under the bending moment of 60 kips-ft. Determined the Maximum compression and tension stress in the concrete and tensile stress in the rebar. The section is uncracked. b-15 in, h=30 in, d= 28 in f=4000 psi, Ec-3,600,000 psf fy= 60,000 psi, Es-29,000,000 psf Rebar= 3 -No. 6 h -As
.ll Asiacell ? 12:33 PM @ 81% HW 4.docx HW4: - The Inverted T section of a L-m simply supported beam has the properties shown in Fig. (4). Find the flange width (b) so that the allowable stresses o ension max =30 Mpa and o compression max.=90 Mpa. 20 mm W KN/m L(m) b(mm) Fig( 4)
Question 3 of 10 View Policies Current Attempt in Progress Answer: Wo A The steel beam has the cross section shown. The beam length is L = 5.8 m, and the cross-sectional dimensions are d = 400 mm, bf = 210 mm, tf = 14 mm, and tw = 7 mm. Calculate the largest intensity of distributed load wo that can be supported by this beam if the allowable bending stress is 160 MPa. A 72 Save for Later Wo B 72 C kN/m - / 10 E ||| d 600 Attempts: 0 of 3 used Submit Answer
Q1) The R.C slab system shown in Figure (1) supported by column line beams and carries a service live load of 5 kN/m and a service superimposed dead load of 3.5 kN/m in addition to its own weight. Slab thickness is 200mm, all beams are (300x600) mm. All columns are 300mm square, use f-25MPA and f=420MP.. According to the ACI-direct design method, determine the following: 6.0m 7.6m 6.0m (a) Design the middle strip bottom bars of the exterior indicated panel shown, in E-W direction. 6.0m 6.0m 7.6m (b)Design the required steel reinforcement at the exterior corner (C). Figure (1)
A simply supported bseam of a beam and slab system, rests on a support of width 450 mm. The clear span of the beam is 10.0 m., The thickness of the slab is 120 mm. The depth of the beam below the slab is 480 mm and the width of the beam is 250 mm. The beam is reinforced with one row of 32 mm diameter steel rods. The total load including the super imposed dead load, live load and its own weight is 25.0 kN/m at service stage. Compute the maximum nominal design shear stress in the concrete.