A reinforced concrete slab (one-way slab with both ends continuous) is built integrally with its supports and consists of three equal spans, each with a clear span of 13 ft. The service live load is 160 psf. Calculate interior support moments for the mentioned slab. Minimum thickness h of nonprestressed one-way slabs Simply supported One end continuous Both ends continuous e/20 e24 /28 Cantilever O a. 7.63 (ft-kips) O b. 4.37 (ft-kips) O c. 5.74 (ft-kips) O d. 6.26 (ft-kips)

A reinforced concrete slab (one-way slab with both ends continuous) is built integrally with its supports and consists of three equal spans, each with a clear span of 13 ft. The service live load is 160 psf. Calculate interior support moments for the mentioned slab. Minimum thickness h of nonprestressed one-way slabs Simply supported One end continuous Both ends continuous e/20 e24 /28 Cantilever O a. 7.63 (ft-kips) O b. 4.37 (ft-kips) O c. 5.74 (ft-kips) O d. 6.26 (ft-kips)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q7/ A precast beam is to be used as a bridge over a small roadway. Concrete dimensions are b= 500 mm, and h = 700 mm. The effective depth d = 600 mm. Concrete and steel strengths are 42 MPa and 420 MPa, respectively. Using approximately one-half the maximum tensile reinforcement permitted by the ACI Code (select the actual size of bar and number to be used), determine the design moment capacity of the girder. If the beam is used on a 9 m simple span, and if in addition to its own weight it must support railings, curbs, and suspended loads totaling 7 kN/m, what uniform service live load limit should be posted?
Q4/ Compact the design bending strength to the reinforced concrete beam has a width b=300mm and effective depth d=525mm, fc-20, fy=300MPa. Suppose that the beam design to achieve a maximum bending according to code.
The beam is simply supported on a span of 6 m and carries a load of 18 KN/m. Use ACI Specifications withfc’ = 17.2 MPa, fs = 124 MPa, n = 12, d’ = 65 mm, and ?concrete = 23.54 KN/m3.(a) service moment (f) use b = 250 mm, d = Answer (round down to nearest 25 mm) + 50 mm(b) fc to take care of dead load(c) k (g) h (h) dead load (i) total load(d) j (j) recompute service moment (k) check effective depth(e) R (l) use 28mmɸ for As (m) check main bar clear spacing
In the built-up girder shown below that has an unbraced length of 25 ft. (L-25 ft) and moment gradient factor of C,-1, determine the maximum flexural design strength. E-29000 ksi Fy-50 ksi PL 25x0.6" PL 35*0.3" PL 25x0.6"
Problem 2: A simply supported beam made of f = 6000 psi concrete spans 80 ft between supports. The beam carries a dead load of 1.6 kip/ft and a live load of 2 kip/ft. a.) Using ACI code requirements, determine V₂ at the critical location. b.) Check if the section meets ACI code requirements for Vs,max. c.) At the critical section, find the required spacing (to the nearest inch) of no. 4 stirrups with a fyt = 60,000 psi. 00 00 00 00 6.5 00 50.25"
None
A rectangular cross section of a beam is under the bending moment of 60 kips-ft. Determined the Maximum compression and tension stress in the concrete and tensile stress in the rebar. The section is uncracked. b-15 in, h=30 in, d= 28 in f=4000 psi, Ec-3,600,000 psf fy= 60,000 psi, Es-29,000,000 psf Rebar= 3 -No. 6 h -As
Q.2 Design the one way slab for the situation shown below; Concrete unit weight is 150 lb/ft3 the only dead load is weight of the slab.
Question 17
I need the answer as soon as possible
AT-Beam has the following properties: bf = 750 mm, bw = 275 mm, d 560 mm, t = 115 mm. Concrete compressive strength fe 21 MPa and steel yield strength fy 415 MPa. T-Beam is under factored moment load of 720 kN-m. Locate the compression block under balanced condition from the extreme compression fiber.
A simply supported bseam of a beam and slab system, rests on a support of width 450 mm. The clear span of the beam is 10.0 m., The thickness of the slab is 120 mm. The depth of the beam below the slab is 480 mm and the width of the beam is 250 mm. The beam is reinforced with one row of 32 mm diameter steel rods. The total load including the super imposed dead load, live load and its own weight is 25.0 kN/m at service stage. Compute the maximum nominal design shear stress in the concrete.