A reinforced concrete beam of 28 ft long is simply supported on both sides. It will carry a superimposed deadload of 2 k/ft and a uniform live load of 4 k/ft. Use f'c-4000 psi and fy=60000 psi, concrete unit weight = 1500.18f. Design the rectangular section in single reinforcement and show complete sketchfyof cross-section, including bar sizes, arrangement and spacing.lb/ft³, h=d+3", and p =

The dead load is .The live load is .The compressive strength of the concrete is .The yield strength…

A reinforced concrete beam of 28 ft long is simply supported on both sides. It will carry a superimposed dead load of 2 k/ft and a uniform live load of 4 k/ft. Use f'c-4000 psi and fy=60000 psi, concrete unit weight = 150 . Design the rectangular section in single reinforcement and show complete sketch 0.18f lb/ft³, h=d+3", and p = fy

A reinforced concrete beam of 28 ft long is simply supported on both sides. It will carry a superimposed dead load of 2 k/ft and a uniform live load of 4 k/ft. Use f'c-4000 psi and fy=60000 psi, concrete unit weight = 150 . Design the rectangular section in single reinforcement and show complete sketch 0.18f lb/ft³, h=d+3", and p = fy

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 415 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars. 1. Determine the tensile steel ratio for positive bending. 2. Determine the depth of the uniform rectangular stress block on the beam section at ultimate stage when subject to positive bending. 3. Determine the design moment capacity in kN•m of the beam in positive bending.
Find the maximum allowable value of P for the column. The cross-sectional areas and working stresses (ow) are shown in the figure. |2P Steel: A = 500 mm2 Ow = 120 MPa P Timber: 4P A = 2000 mm? Ow = 12 MPa Concrete: A = 8000 mm? O = 16 MPa
Ultimate Design Single concrete
A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 350 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars. 1. Determine the maximum steel ratio if the beam is singly reinforced in negative bending with the given material strengths and the tensile strain is limited to 0.004 upon crushing of concrete. Write the answer in 5 decimal places only. 2. Determine the maximum steel ratio if the beam is singly reinforced in positive bending with the given material strengths and the tensile strain is limited to 0.005 upon crushing of concrete. Write the answer in 5 decimal places only.
5. The beam shown is reinforced for positive moment with three epoxy-coated #11 bars. The bars terminate at the center of the supports. Neglecting beam weight (concentrated loads are very heavy), determine if the required development length is satisfied. Assume As required = 4.55in², 2 in. clear cover on all sides of the longitudinal reinforcement, normal weight concrete, #3 stirrups @12 in o.c., f'c = 5000 psi and fy = 60,000 psi. 8 ft | Pu 20 ft Pu 8 ft ge2 of 56 30 in b=14in. ed 5/15/2020 As = 3-#11
A beam has a width of 280 mm and 490 mm overall depth. Concrete cover is 65 mm from the centroid of bars. Concrete compressive fc' = 24 MPa. Steel yield strength are fy=415 MPa and fy = 275 MPa for ties. Determine the shear strength provided by concrete using simplified method a) If the beam is subjected to shear and flexure only, and b) If the beam is subjected to axial compressive force of 124kN.
Question 31 A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 350 MPa for 20-mm bars and fy = 230 MPa for 16-mm bars. Determine the design moment capacity in kN∙m of the beam in negative bending. Write the answer in 2 decimal places only.
Avoid truncation in the middle of solution (3 decimals for final answer )
If the given beam section is used for a simply supported beam 5.0 m span, using fc = 21 MPa and fyt = 280 MPa: 10-mm-dia 425 mm @ 200 mm 500 mm -275 mm 75 mm 25. Calculate the nominal shear strength of concrete, using simplified formula of NSCP 2015. = kN 26. Calculate the nominal shear strength of the stirrups, Vg = kN. 27. Calculate the design sectional shear strength of the beam = kN 28. Determine the maximum factored uniform load in that can be sustained based on shear strength of the cross-section only. = kN/m 29. Determine the maximum live load in that can be sustained based on shear strength of the cross-section only. = kN/m 30. If the total factored uniform load is 60 kN/m, calculate the ultimate shear force at critical section for shear in kN. = kN INPUT ALL ANSWERS ROUNDED TO WHOLE NUMBER
Given are the following: 300 Unit weight of concrete = 24 kN/m3 f'c = 28 Mpa fpe = 850 MPa fpu = 1350 MPa Aps = 750 mm? foy = 1280 MPa Beam is a simple span and have a length of 24m. Use bonded tendons as prestressed reinforcement. A. Determine the value of fps (MPa) B. Determine the nominal moment strength (kN-m) 750 850
Help 35 minutes
Given a concrete column that would be required to support loads of Pu=400kips and Mu=50 kip-feet, we will determine the column interaction curve and decide if the column is adequate for this particular application. The column will be a 14”x14” square, tied column with #9 bars at the corners. The center of the reinforcement in each corner is 3” from each of the sides. The f’c of the concrete is 4 ksi and the reinforcement is Grade 60. Determine if the column is acceptable for this application. Calculate the value of Mu and Pu.