A rectangul3 the water. The gate is 4 feet in length and 5 feet wide. Answer the following questions. vater door shown in the figure below is hinged 3 1. Calculate the resultant force on the door. 2. Calculate the location of the resultant force on the door. 3. Neglecting the weight of the door calculate the minimum force (FA) needed to keep th door closed You may assume the outer surface of the door and the surface of the water are both exposed

A rectangul3 the water. The gate is 4 feet in length and 5 feet wide. Answer the following questions. vater door shown in the figure below is hinged 3 1. Calculate the resultant force on the door. 2. Calculate the location of the resultant force on the door. 3. Neglecting the weight of the door calculate the minimum force (FA) needed to keep th door closed You may assume the outer surface of the door and the surface of the water are both exposed

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please solve this problem.asap. Thank you!
Question 2 A concrete block is attached to the gate as shown. If the water level is 1.5 m from the bottom of the container, there is no reaction force at A. What would be the reaction force for the level shown? Note 1: Specific gravity of concrete is 2.7. 0.70 m 40 2.2 m m 0.80 m
A. Determine the magnitude of the hydrostatic force acting on the gate using the HYDROSTATIC PANEL EQUATIONS. Express your answer in kN. B. Determine the minimum force P required to open the seawater gate. Express your answer in kN. Show complete solution (Round off ONLY the final result to three decimal places. Indicate the unit of your final answer)
a. Determine the magnitude and direction of the hydrostatic force acting on the gate using PRESSURE PRISM CONCEPT. Illustrate and label the pressure diagram/prism as part of your solution. Express your answer in kips. b. Determine the magnitude and direction of the force exerted on the plate by the ridge. Illustrate and label the FBD of the force system. Express your answer in kips.
Read the question carefully and give me right solution with clear steps. Note: I have other websites solution again don't give me same solution. Rating depends on your solution thank you
The 600-lb, 20ft-wide rectangular gate shown is hinged at B and leans against the floor at A making an angle of 45° with the horizontal. The gate is to be opened from its lower edge by applying a normal force P at its center. A. Determine the magnitude of the hydrostatic force acting on the gate using the HYDROSTATIC PANEL EQUATIONS. Express your answer in kips. B. Determine the minimum force P required to open the seawater gate. Express your answer in kips.
Read the question carefully and give me right solution according to the question. Don't copy from other websites solution
The 90-cm square gate, hinged at one end, weighs 2 kN. Assuming the chain weighs 120N a. What is the force of oil on the gate?b. What is the force of water on the gate?c. How much force F is needed to open the gate?
A. Determine the magnitude and direction of the hydrostatic force acting on the gate using the PRESSURE PRISM CONCEPT. Illustrate and label the pressure diagram/prism as part of your solution. Express your answer in kips. B. Determine the magnitude and direction of the force exerted on the plate by the ridge. Illustrate and label the FBD of the force system. Express your answer in kips. Show complete solution (Round off ONLY the final result to three decimal places. Indicate the unit of your final answer)
A. Determine the magnitude and direction of the hydrostatic force acting on the gate using the PRESSURE PRISM CONCEPT. Illustrate and label the pressure diagram/prism as part of your solution. Express your answer in kips. B. Determine the magnitude and direction of the force exerted on the plate by the ridge. Illustrate and label the FBD of the force system. Express your answer in kips.
Water flows out of the reducing elbow at 0.4 ft³ /s Part A (Figure 1). The pipe and elbow and the water within have a total weight of 250 lb. The water is discharged to the atmosphere at B. Determine the horizontal component of force that are necessary to hold the elbow in place at A. Express your answer using three significant figures. vec F = lb Submit Request Answer Figure 1 of 1 Part B 0.25 ft Determine the vertical component of force that are necessary to hold the elbow in place at A Express your answer using three significant figures. Πν ΑΣφ ? vec 3 ft F, = 5.47 lb Submit Previous Answers Request Answer 60° X Incorrect; Try Again; 5 attempts remaining 0.5 ft
A 40-lb roller, of diameter 8 in., which is to be used on a tile floor, is resting directly on the subflooring as shown. Knowing that the thickness of each tile is 0.3 in., determine the force P required to move the roller onto the tiles if the roller is (a) pushed to the left, (b) pulled to the right. 30°