A 40-1b roller, of diameter 8 in., which is to be used on a tile floor, is resting directly on the subflooring as shown. Knowing that the thickness of each tile is 0.3 in., determine the force P required to move the roller onto the tiles if the roller is (a) pushed to the left, (b) pulled to the right.

A 40-1b roller, of diameter 8 in., which is to be used on a tile floor, is resting directly on the subflooring as shown. Knowing that the thickness of each tile is 0.3 in., determine the force P required to move the roller onto the tiles if the roller is (a) pushed to the left, (b) pulled to the right.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A high-strength steel band saw, 27 mm wide, runs over pulleys 1100 mm in diameter. What minimum thickness of the steel band can be used without exceeding a flexural stress of 350? Assume E = 210 GPa. Answer must be in mm.
Answer the problem question show the correct solution and box the final answer. Use two decimal places
a)Calculate the 5N force, the Vicker Hardness measurement with one corner of the pyramid trace 5mm and the other 8mm. b)Calculate the force of 5N, the Brinell hardness measurement with a ball diameter of 5mm and a trace diameter of 8mm on the part.
Minimum of 3 decimal places in all computations.
A steel loop ABCD is placed around a 1.0 in. diameter aluminum rod AC. Cables BE and DF, each of 0.5 in. diameter, are used to apply the load Q. What is the largest allowable Q if the axial stress in cable BE stays under 23 ksi while the max axial stress in the aluminum rod AC is under 13 ksi? Reference: Beer, et.al., 7th Edition Mechanics of Materials 9 in. Į 9 in. ↓ A 12 in. 1 in. 4 E * F B D Q' 12 in. in. in. C
PROBLEM TO SOLVE: 600 mm 400 mm Using fe' = 28 MPa, Mmax = +320 kNm Determine the following: a. Cracking Moment (kNm) 6-25mm diam. b. Compressive Stress felt by concrete (MPa) c. Tension Stress felt by the tension bars (MPa)
* Fixed-Fixed bar was 20 centigrade degree at room temperature, Determine the thermal stress when the bar is heated to :110 degree A Lo Est = 200 Gpa ast 11.7 μm/m°C Ast = 200 mm² + 210.6 MPa (compression) + 210.6 MPa (Tension) _187.2 MPa (compression) +187.2 MPa (Tension) _187.2 MPa (Tension) _210.6 MPa (Tension) +187.2 MPa (compression) O 210.6 MPa (compression)
A high-strength steel band saw, 24 mm wide, runs over pulleys 900 mm in diameter. What minimum thickness of the steel band can be used without exceeding a flexural stress of 310? Assume E= 230 GPa. Answer must be in mm.
A high-density polyethelene (HDPE) [E = 780 MPa; v = 0.46] rod has a diameter of 100 mm before load P is applied. In order to maintain certain clearances, the diameter of the rod must not exceed 102 mm when loaded. What is the largest permissible compressive load P that can be applied to the HDPE rod? P. High-density polyethelene (HDPE) rod Answer: P = i P kN
Please show intermediate steps including free body diagrams, equations used, and problem setup so that your approach can be followed.
SHOW COMPLETE SOLUTION AND ILLUSTRATION
Show complete and detailed solution. Draw illustrations