A rectangular tank 6 m long, 3 m wide and 2m deep contains water to a depth of 1 m. It is accelerated horizontally at 2.5 m/s2 in the direction of its length. Determine the maximum pressure intensities at bottom. Unit of the Correct Answer: kPa Group of answer choices 17.31 31.17 13.71 71.13

Q: Water flows steadily through a smooth circular tube of 10 cm diameter at a flow rate of 2 kg/s. The…

A:

Q: Determine the value of hin meters indicated in the

A:

Q: Q3. A vertical wall (5 m long) has a fluid (sp. Gravity 0.8) on one side and another fluid (sp.…

A:

Q: The rectangular bin with an inclined gate AB is filled with water to the depth shown. Determine the…

A:

Q: A vertical rectangular gate 1.6 m wide and 5.6 m high is submerged in oil (SG=0.91) with its bottom…

A:

Q: 12. What will be the total pressure (in kN) on a vertical square lamina submerged in a tank of oil…

A: Given Data : S=0.9

Q: 7. Determine the difference in pressure APAB between locations A and B in kilopascals (kPa) based on…

A:

Q: A water pipe runs vertically through a tall building, with a flow rate of 0.2 m³/s. The diameter of…

A:

Q: weight of the liquid. 4. The absolute pressure in water at a depth of 8m is read to be 175 kPa.…

A:

Q: 2. A closed, 5-m tall tank is filled with water to a depth of 3 m. The top portion of the tank is…

A:

Q: Fluid flows in a 2.5-mm-ID horizontal tube. Find the pressure drop per meter. =0.06 Pa ·s, RD=0.725,…

A: Find velocityRe=ρvDμ205=1000×0.725v2.5×10-3m0.06v=6.7862ms-1

Q: Water at T = 25°C is drawn from an underground detention tank and discharged into a drain using a…

A: Temperature is,To determine:Part A): Available NPSHPart B): Required NPSH

Q: Chamber A SAE 30 oil Chamber B Carbon tetrachloride -N-

A:

Q: Q1: An Orifice meter is inserted in a pipe of 25 cm diameter. Water flows through the pipe and the…

A: The given data is shown below:

Q: 3m 9m W2 8m W1 6m

A:

Q: 3. The open trapezoidal tank shown in the figure is initially filled with oil (SG = 0.80) up to a…

A:

Q: Q11: Find the depth a in the Tank shown in Figure 10, if the pressure at point D is P, = 30 (KN/m2).…

A: Given data  Pressure at D Specific gravity  Heights Air Unit weight  Water level

Q: Q11: Find the depth a in the Tank shown pressure at point D is PD = 30 (KN/m2).

A:

Q: The diving bell has the shape of a frustum of a cone (circular) with a closed flat top and open…

A:

Q: Estimate the Hazen-Williams pipe roughness factor, C, for a 250-millimeter (mm) diameter water main.…

A: To determine the Hazen-Williams pipe roughness factor (C) for given flow parameters.   Given,…

Q: A 6 cm diameter pipe with water flowing at a discharge of 1/min. At a section, the pipe has a sudden…

A:

Q: A 1.2m diameter open vessel, 2m high is filled with oil s.g = 0.85 at a depth of 1.6m and rotated at…

A:

Q: 3.) Determine the total pressure and center of pressure on a circular plate of diameter 3700mm which…

A: The pressure force on a submerged body is equal to product of pressure at centroid and area of body.…

Q: Vater flows through a horizontal 60-mm-diameter galvanized iron pipe at a rate of 0.018 m³/s. If the…

A: Given data :-  Diameter of pipe (D) = 60 mm = 0.06 m  Flow rate (Q) = 0.018 m3/sec  Pressure drop =…

Q: a) What is traffic management? b) Enumerate and explain four (4) types of traffic management…

A: The traveling, visiting places, and imports and exports are only done by the transportation facility…

Q: he hole by a distance x. Given: h = 0.85 m, a = 0.4 m, b = 0.7 m. Determine: by what distance x do…

A: Given:- h = 0.85 m, a = 0.4 m, b = 0.7 m.  To find:- by what distance x do we have to move the…

Q: 30'

A:

Q: Answer fast please clarify all question.

A: Solution:To calculate the velocity of the pressure wave in the pipe and plot the variation of…

Q: PROBLEM 2 The pressures at polnts 1 and 2 of the water plpe shown are 300 kPa and 100 kPa,…

A:

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?