A rectangular sign over a store has a weight of 250 lb, with the center of gravity in the center of the rectangle. The support against the wall at point C may be treated as a ball-and-socket joint. At the corner, D support is provided in the y-direction only. Calculate the tensions Ty and T2 in the supporting wires, the total force supported at C (in r and 2 direction), and the lateral force R supported at D.

Q: An object weighing 51kg is suspended from two ropes that are attached to the ceiling 1.5m apart. The…

A:

Q: An object is being held off the ground by a crane on the right and 4 constructions with a rope on…

A:

Q: A wire is stretched tight between two pylons, one of which is shown in Fig. to the xy-plane and…

A: Draw the free-body diagram for joint D.

Q: The 200 kg skid steer loader is act at the centre of gravity (G) as shown in Figure Q3. If the…

A: Draw the free-body diagram of the skid loader.

Q: The T-shaped structure is embedded in a concrete wall at A and subjected to the force and the…

A: The value of force is The moment is The dimension are The net resultant moment about A is

Q: Calculate the forces acting at pin A, pin B, and pin C. 6 m 5 kN 1.5 m y 1.5 m x OB 3 m 3 m

A: Calculate the forces acting at pin A, pin B, and pin C.

Q: Identify all forces and moments on the fixed support B and calculate them. Find the total magnitude…

A: Given the distanceAB= 4 feetConversion from feet to meters

Q: A Christmas decoration is suspended by two wires. Two equal tension forces in the wires each act at…

A:

Q: Problem 4: A ball and socket joint A and two wires are used to hang a sign of mass 120 Kg (1177 N).…

A:

Q: The figure shows a sign, fabricated from thin, uniform, flat, stainless-steel bars with a weight per…

A: The weight per unit length of sign is

Q: Three hydraulic cylinders control the motion of the backhoe arm and bucket in the given figure. In…

A:

Q: Question 2 (Type B): A triangular thin plate is supported by a ball-and-socket joint at A and a…

A:

Q: Quiz 1: Determine the force in each assigned member as below of the truss. State if the members are…

A: solution given below

Q: The structure is made of the light bar AB and the 50-kg uniform bar CD. Compute the magnitude of the…

A:

Q: 2. Find the horizontal and vertical forces at Point C as it acts on Member BD.

A:

Q: 1. The frame shown in the figure is hinged to rigid supports at A and E. Find the components of the…

A: determine- hinge forces at A and E                    forces in member BC and BD

Q: please answer this question with explination, thankyou !

A: Step 1:Step 2:

Q: The truss shown is used to support a 9 kg block with a pin at A and a roller at E. Given a = 1.1 m,…

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.