A rectangular plate is supported by three cables as shown. Knowing that the tension in cable AD is 534 N, determine the components of the force exerted on the plate at D. 130 480 B 320 450 C Dimensions in mm The x component of the force is The y component of the force is The z component of the force is 250 D 360 360 X N. N. N.

A rectangular plate is supported by three cables as shown. Knowing that the tension in cable AD is 534 N, determine the components of the force exerted on the plate at D. 130 480 B 320 450 C Dimensions in mm The x component of the force is The y component of the force is The z component of the force is 250 D 360 360 X N. N. N.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two cables are tied together at C and are loaded as shown. Knowing that P = 500 N and angle alpha is 50 degrees, determine the tension in cable AC.
Question 5 Cables AB and AC are connected at point A at a height of 10 m from ground. The magnitude of the force F along AC is 850 kN. (a) Determine the magnitude of the components of the force F acting along and perpendicular to the cable AB. (b) Determine the angle made between the force F and cable AB. F 12 m 14 m 16 m
In the force system, determine (a) The component of the force F acting along the cable AC. (b) The angle the force F makes with cable AC. 1.5 m B 1.5 m 1m F- 560 N 3 m 3m
B8
A vertical pole is subjected to a pull of 620N in the yz plane and 15 deg below the horizontal. The guy wires AB and AC are attached to supports in the xy plane. The pole rests in a socket. What is the tension in each cable?
Find sag Yc and determine the largest force, F, that can be sustained by the cables if the maximum tension allowed is 720 N.At point C, what is the largest mass, M, that can be sustained by the cables if the maximum tension is 720 N.What is the tension in cable CD in Newtons (N)?What is the value of sag Yc in meters (m)?
solve for the tension at cable AB and the reaction at E, considering the weight of bent bar CBDE = 420 lb *pls use 3 decimal places all throughout the solution
Situation 6: Z-axis Three tension cables as shown on the figure are acting on a vertical post to remain its position at E. If the tension in cable AC is 4 N, determine the tension developed in the other cable so that the resultant at A X-axis y-axis will be vertical. sourcowa eHeocom 1 m m 4 m D
10° A 60° If the maximum tension force the cable AB could carry is 1500 N before breaking, and the maximum compressive force the pole AC could carry is 2200 N before buckling, what is the maximum value of Pin Newtons
Solve for the force in segment CD in the cable system shown. please show all work in detail. Thank you
No. 1 1.12 m 0.96 m 0.98 14 1.28 m 1.20 m steel rod is bent into a semicircular ring of radius 0.96 m and is supported in part by cables BD and BE which are attached to the ring at B. Knowing that the tension in cable BE is 250 N, determine the components of this force exerted by the cable on the support at E.
The hinge at A and cable BDC support beam ABC. Cable BDC passes over the pulley D that is pinned to the ceiling. (Assume that the +x-axis is to the right and the +y-axis is up along the page. Due to the nature of this problem, do not use rounded intermediate values in your calculations or answers.) Determine the tension in the cable in newtons - ? Determine magnitude and direction - magnitude in newtons Ax- ? Ay- ?