A rectangular duct must connect with a circular duct. The rectangular ductmeasures 6 inches by 7 inches. The circular duct has a diameter of 7 inches.Which duct has the smaller cross-sectional area?

Q: Round ductwork measures 20 centimeters in diameter and is 14 meters long.What is the volume of this…

A:

Q: 4. To what height will water rise in a 3mm-diameter glass tube at 20°C? Assume Owater = 0.073 and…

A: The problem is about the height of capillary rise in the tube. Using the standard formula for rise…

Q: An illegal connection was detected along a water 400 mm water supply line made with cast iron pipe…

A:

Q: Oil (sg=0.87) flows from A to E as shown. The head loss is assumed to be as follows: A to B = 0.45…

A: head losses from A to E = 0.45 V2B2g + 8.75 V2182g + 0.12 V2182g + 9 V2B2g Solving we get ; HL =…

Q: 1. The represents the roughness of a pipe whereas the Icoefficient accounts for the roughness of the…

A: This question is related to the Fluid Mechanics from Civil Engineering. This question is based on…

Q: A test is set-up as shown in the figure. A cylindrical mold 4" in diameter is filled with silt to…

A:

Q: Discuss the experimental determination of orifice coefficients. What value are these coefficients to…

A:

Q: From the given figure which of the following is/are correct? a. DFAB = DFCB b. FEMAB = FEMBA c. DFBA…

A: For given figure

Q: An old pipe of diameter 2.5” is carrying water at a velocity of 4 ft/s. Determine the Reynolds…

A: Given data in question  Diameter of pipe  Length of pipe  Velocity of flow Kinematic viscosity  To…

Q: A glass capillary tube, 2 mm in diameter, is placed on top of a mercury layer. Calculate the height…

A:

Q: B) What is the difference between? 2-Internal and External flow

A: Internal flow can be defined as a type of flow bounded by solid surfaces. Such type of internal flow…

Q: An old pipe of diameter 2.5” is carrying water at a velocity of 4 ft/s. Determine the Reynolds…

A: Given: Diameter of pipe, D = 2.5 in Velocity of flow, v = 4 ft/s Length of pipe, L = 200 ft…

Q: for

A: OSTWALDS EQUATION:time=A×μρμ=viscosity=0.98poise=0.98×0.1 Nsecm2ρ=0.02gcc=20kgm3 A=?

Q: Stress analysis Task Question / Calculate the critical design loads applied to the Stirling Engine…

A: Please find the answer in the below attachments

Q: Consider a constricting portion of a pipeline carrying water vertically downward as pictured. At the…

A: Given:-  Diameter at point 1 (d1) = 7 inches  Velocity at point 1 (V1) = 10 ft/s  Height of point 2…

Q: From the given figure which of the following is/are correct? a. DFAB = DFCB b. FEMAB = FEMBA c. DFBA…

A:

Q: Oil (sg=0.87) flows from A to E as shown. The head loss is assumed to be as follows: A to B = 0.45…

A:

Q: Water is flowing at a rate of 8 ft³/s in a rectangular channel with a 2 ft water depth and a 4 ft…

A:

Q: While constructing a building, an engineer need to fix two steel beams together using a bracket as…

A: Answer; To construct a G-code program for drilling hole number 3 only by using absolute coordinate…

Q: Define Hydraulics. Briefly explain minor head losses in pipes.

A: Hydraulics is the science of conveying the motion or force of the liquid and the liquid is confined.…

Q: 1. Water flows through a 12 inches by 6 inches venturi meter at the rate of 1.49 ft/s and the…

A:

Q: After being filled to a depth d with SAE 30 oil (SG = 0.91), a glass is placed to float in a tank of…

A: Depth upto which SAE oil is filled in a glass to make it float on water = d , Specific Gravity og…

Q: Problem 3.33 Given: V Solution: h Air Space Water As shown, an air space above a long tube is…

A:

Q: Describe about the Water in Capillary Tubes.

A: Capillary action happens because the effects of cohesion and adhesion make water sticky.

Q: Q1) If a = 45°, calculate the resultant of the three forces acting on the brick placed on a surface…

A: Reference : Engineering mechanics , Forces and resultant forces.The FBD free body diagram can be…

Q: inflow water 1.50" Sand Silt Sand H2 = 0.30 ft h = 1.25 ft Silt H1 = 0.20 ft outflow

A:

Q: Apply the grid method to each situation. a. If the pressure is 15 inches of water (vacuum), what is…

A: a) P = 15" of water         = 15*2.54/100 m of water         = 0.381 m of water          =…

Q: What is the system pressure when the cylinder retracts? is it more or less than the pressure when…

A:

Q: In a container filled with each of the following materials, at a porosity of 40%, determine the…

A:

Q: hich of the following statements is not true? The nominal pipe size (NPS) is an international set of…

A: We have provided four statement about the Nominal Pipe Size (NPS).We have to choose the incorrect…

Q: C-4 m- T .G 60° 4.5 m

A:

Q: inflow water 1.50" Sand Silt Sand H2 = 0.30 ft h = 1.25 ft Silt H1 = 0.20 ft outflow

A:

Q: Describe the pressure meter test.

A: Pressuremeter:

Q: water up to a height of

A: To find : Location of center of pressure

Q: A rectangular plate of aluminum with a specific gravity of 2.7 is floating between a mercury-water…

A:

Q: 2. A beaker contains water up to a certain height as shown. If the water is allowed to get…

A: Steady flow: In this type of flow,the flow parameters like density,velocity,pressure ,cross section…

Q: A 2-foot diameter pipe carries stormwater discharge from a site. The concrete pipe was designed with…

A: Given: The diameter of the pipe is 2 ft. The slope is 0.8 ft per 90 ft. The depth of flow is 0.8 ft.…

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.