A rectangular canal, 6.45m wide and 1.45m deep lined with smooth stone (n=0.013) has a hydraulic slope of 0.001. What savings in earth excavation (m3) were introduced using the most efficient rectangular section but adhering to the same discharge and slope? Channel is laid 5m long.

Q: Compute the "b" and "d" of a trapezoidal channel if it is most efficient to convey a 6.35 cu.m./s of…

A:

Q: need the answer as soon as possible

A:

Q: A new road is to be constructed with formation width of 10 m, side slopes of 1 vertical to 0.5…

A: Given data: Formation width = 10 m side slope = 1 V: 0.5 H distance between the sections = 10 m…

Q: A rectangular canal, 6.45 m wide and 1.45 m deep lined with smooth stone ( n = 0.013) Has a…

A:

Q: (b) Design a circular drainage pipe to carry 3.6 m³/s of stormwater. The slope and length of the…

A:

Q: For a V-shaped concrete lined channel with total included angle of 80°, and a depth of 3 m if the…

A:

Q: Given the discharge of the trapezoidal canal of 3 m3/sec., flow velocity of 1.37 m/sec, bottom width…

A: Determining the Side Slope of a Trapezoidal Canal Given the following parameters of a trapezoidal…

Q: An open channel having a slope of 0.0063 Is to carry 10 m3 /s. The channel material has an n value…

A: For most efficient triangular channel with given data it has been asked to find hydraulic mean…

Q: A rectangular canal, 6.45m wide and 1.45m deep lined with smooth stone (n=0.013) has a hydraulic…

A:

Q: Calculate the quantity of the earthworks in cubic meter for a canal embankment of 100 m long having…

A: Given data- Length d=100 mheights of 3m and 5 mwidths =2m and 4m slope 2:1

Q: A cutting of 12 m depth is to be made for a road as shown in below figure. The soil properties are:…

A: The given data is: Depth of cutting=12 m c=24 KN/m2 ϕ=15°γ=18 KN/m3

Q: Calculate the quantity of the earthworks meter for a canal omb

A: Trapezoidal method: -It is defined as a numerical method which is used for evaluating the area of…

Q: 6.11. A power canal of trapezoidal section has to be excavated through hard clay at least cost.…

A:

Q: 0.0054 Is to carry 5 m3 /s. The channel material has an n value of 0.051. For a most efficient…

A:

Q: A storm drainage channel has the shape shown in Figure 5. It is made of unfinished concrete and has…

A: To determine the hydraulic radius and the normal discharge at different normal depth for a given…

Q: If cross sectional area of an embankment at 30 m intervals are 20, 40, 60, 50 and 30 m²…

A:

Q: A rectangular channel 5.2 m wide by 1.4 m deep was laid to have a hydraulic slope of 0.001. Using n…

A:

Q: A rectangular channel with a width of B = 2 m drains water with a discharge of Q = 2,4 m3/s. The…

A: Width of channel (B) = 2m Depth at upstream = 1.5m Area= 2 x 1.5 =3m2 Discharge = 2.4 m3/s Perimeter…

Q: A rectangular concrete channel (n = 0.014) has a bottom width of 12.0 m, a water depth of 6.0 m and…

A: A rectangular concrete channel-Manning's constant n=0.014,Bottom width b =12 m,Water depth d =6…

Q: A dam cross-section is a square facing a water depth of D=15m. Assuming a 1m strip for analysis and…

A: Given data,  FOS for overturning = 2 D = 15 m Coefficient of friction = 0.5  To find out the…

Q: discharge = 10.8 m^3/sec average velocity = 0.65 meters/sec side slope = 2H : 1V bottom width =…

A:

Q: Q.1 Above Figure represents floor of a hydraulic structures rested on fine gravel with seen…

A: As per Lanes Theory; let us consider d1 as upstream depth and d2 as downstream depth, then,  Floor…

Q: An earth canal is to carry 10.8 m³/ s at a mean velocity of 0.65 m /s. the side slopes are to be 2…

A: Given data, Discharge Q = 10.8 m3/s V = 0.65 m/s Slope = 2H:1V Width = B Depth y = 0.25×width (B)…

Q: Given: A small hydraulic excavator will be used to dig a trench in common earth (bucket fill factor…

A: Consider the following given data The soil type is common earth Bucket fill factor=B=0.95Trench…

Q: A rectangular channel 6 m wide and 1.5 m deep has a slope of 1 in 1200 and is lined with good rubble…

A:

Q: width of rectangular channel = 3.6 meters discharge = 2.7 m^3/s Assume n = 0.012   What is the…

A:

Q: The ratio of the upstream depth to downstream depth in a hydraulic jump for a rectangular,…

A:

Q: A canal having side slope 1 to 1 is proposed to be constructed in a cohesive soil to a depth of 5 m…

A:

Q: A rectangular channel 4.82 m. wide by 1.33 m. deep is lined with a smooth stone (n = 0.014), well…

A: Find Flow…

Q: 5. Draw the sketch of the following cross section of channel and indicate the specified dimensions.…

A:

Q: An concrete lined trapezoidal channel (n = 0.013) has an 6-foot wide base, slide slopes of 2.5, bed…

A: Let the normla depth be 'y'so,A=6y+2.5y2P=6+2y1+2.52so,Using mannings…

Q: Compute the "b" and "d" of a trapezoidal channel if it is most efficient to convey a 6.35 cu.m./s of…

A: Data is as given

Q: Question 6 Determine the slope of the rectangular channel with following conditions: Channel width =…

A:

Q: A canal is proposed to be made in soil having cohesion 25 kN/m2, p' = 0° and void ratio of 0.792 and…

A: Given- Cohesion of soil C=25 kN/m2ϕ'=0ovoid ratio-e=0.792G=2.65Side slope=1:1FOS=2.5Stability no.…

Q: Two channels sections the first is rectangular with water depth = 3 m and width=3. the second sec.…

A:

Q: Find the hydraulic radius Wetted area=6.25 m2 Wetted perimeter=7.5 m

A:

Q: Here

A:

Q: • Q = 18 m^ 3 /s • Rectangular channel, 3 m wide • Unfinished form concrete channel • occurs at a…

A:

Q: A power-law channel section is to be excavated to accommodate 15 m³/s when flowing full. The channel…

A: Q= 15 m3/secS=.0007n=0.015y=1.5 mTo determine-Equation for best hydraulic power law channel section

Q: A rectangular channel 6 m wide by 1 m deep is laid on a slope of 0.001 has a roughness coefficient…

A:

Measuring site work, Excavation and Piling

Bid drawings typically include very little material about the precise requirements of site work operations, measuring site work and excavation work differs from measuring most other works on a construction project. The actual site work conditions are not provided and also the dimensions of the excavations are not known during the pre-construction phase. The precise measurement of the excavation and backfill of the earth material and topsoil is important for a contractor to decide upon the total cost required for the process. All the works should be carried out under OSHA (Occupational Safety and Health Administration) standards to ensure the safety of the workers.