A rectangular boat 8 m. long by 6 m. wide and “2.0” m high is submerged in water by 1.8 m. Assume water is fresh. a. Find the total draft after P is placed at the edge at the boat without causing it to sink. b. What is the maximum P that can be placed at the edge of the boat without causing it to sink. c. Solve the maximum P if the boat is submerged in seawater with a density at 1026 kg/cu.m.

A rectangular boat 8 m. long by 6 m. wide and “2.0” m high is submerged in water by 1.8 m. Assume water is fresh. a. Find the total draft after P is placed at the edge at the boat without causing it to sink. b. What is the maximum P that can be placed at the edge of the boat without causing it to sink. c. Solve the maximum P if the boat is submerged in seawater with a density at 1026 kg/cu.m.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rectangular tank 3 m x 4 m is 5 m high with 2 orifices placed at a vertical distances of 0.5 m and 1m from the bottom respectively. Both orifices are 100 mm diameter with C=0.607. Determine the: show complete solution a. How long will it take to lower the water at tank by 2 m in seconds?b. How long will it take for the water surface to be at the same level as the upper orifice in seconds?
Choose whether the statement is TRUE or FALSE. * TRUE FALSE The absolute pressure is equal to the gage reading. Hydrostatic force acting on a submerged plane area increases as the depth of immersion increases. The pressure on the base of a liquid column will depend upon the shape of the column. The center of pressure on a submerged plane will be at a lower level with respect to the centroid. The unit of eccentricity is the same as unit pressure.
6. From the figure shown. Find the pressure head at A when fluid A is seawater (1.03), Fluid B is (s = 2.87); z = 12 in; y = 8 ft Fluid A Fluid B y Sea water
H =2m Seawater y = 0.2x2 y 25 m The concrete seawall given in Figure 4 has a curved surface and restrains seawater at a depth of 2 m. The trace of the surface is a parabola as illustrated. Determine the force of the fluid force (per unit length) with respect to an axis through the toe (point A). 1024kg/m³) (Y seawater = -X
In the figure below, determine the force F (newton) to balance the weight of the cylinder. |ylinder W 44 kN A = 0.323 m? F = ? Plunger, a = 0.00323 m? 4.6 m YOil, s = 0.78 YOil, s = 0.78 Assume that the weight
Choose the best answer among the following choices stated in each problem. Your choice must be supported with complete solution
Topic: Fluid mechanics Please solve for: Final metacentric height.
Suppose the impeller in the preceding question supplies 10 kW of water power and is placed in a tank 4 m square and 4 m deep. Determine the velocity gradient G (s ¹). The water viscosity is 1.31 x 10-3 Pa-s.
Water flows in a vertical channel. Use the given data to find the frictional pressure drop from the inlet to the exit of the channel. Compare the calculated values for △Pfriction by using the Homogenous, the Reddy, the Friedel, and the Thom model. Data: H = 6 ft D = 0.145 ft P = 1000 psia X = 8% Vi = 3 ft/s T= 522 F
Consider the pressurized horizontal pipe network consisting of three pipes arranged in series. The characteristics of each pipe are summarized in the table. The flow of water at Node A is Q = 5 cfs and the pressure head at Node A is yA = 200 feet. The temperature of the water is 60° F. a) Determine the friction head loss hfric in feet in Pipe 1. b) Determine the friction head loss hfric in feet in Pipe 2. c) Determine the friction head loss hfric in feet in Pipe 3. d) Determine the pressure head ys in feet at Node B. e) Determine the pressure head yc in feet at Node C. f) Determine the pressure head yo in feet at Node D. Flow Friction Pressure Diameter Length Friction (feet) (cfs) head Нead Pipe (inches) factor f Kpipe loss (feet) Node (feet) 1 16 500 0.011 5 A 200 2 12 1000 0.013 B 3 10 750 0.015 D Node Node Node Node A в D 5 cfs 5 cfs Pipe 1 Pipe 2 Pipe 3
A reservoir contains two different fluids is shown in the figure. The height of the water is 8 m, and the height of the oil (SG = 0.86) is 4 m. a. Determine the density of the oil. b. Determine the pressure between the oil and water in kPa. C. Determine the pressure at the bottom of the reservoir in kPa. OIL WATER