A rectangular beam with a width of 300 mm and total depth of 450 mm and reinforced with 4- 25 mm dia. bars with concrete cover to the center of the bar equal to 65 mm. It is loaded with a total dead load of 30.4 kN/m and a live load of 19.4 kN/m and has a simple span of 6.2 m. Use f'c = 30 MPa and fy = 416.3 MPa. Answer the following: (1) Compute the moment of inertia of a cracked transformed section, (2) Determine the instantaneous deflection of the beam, (3) Compute the total deflection after 3 months due to 30% sustained live load. " Use the editor to format your answer Formula, table for item # 1 above. (Mcr ]ler Ma %3D Ма T 1+ 50p' 5 yrs. Or more 12 mos. 2.0 1.4 6 mos. 1.2 3 mos. 1.0

A rectangular beam with a width of 300 mm and total depth of 450 mm and reinforced with 4- 25 mm dia. bars with concrete cover to the center of the bar equal to 65 mm. It is loaded with a total dead load of 30.4 kN/m and a live load of 19.4 kN/m and has a simple span of 6.2 m. Use f'c = 30 MPa and fy = 416.3 MPa. Answer the following: (1) Compute the moment of inertia of a cracked transformed section, (2) Determine the instantaneous deflection of the beam, (3) Compute the total deflection after 3 months due to 30% sustained live load. " Use the editor to format your answer Formula, table for item # 1 above. (Mcr ]ler Ma %3D Ма T 1+ 50p' 5 yrs. Or more 12 mos. 2.0 1.4 6 mos. 1.2 3 mos. 1.0

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

learn Determine the reaction forces for beams B-1, B-2, and B-3. Column A Column B Girder G-1 open Girder G-2 L1 L1 L1 • Live load = 30 psf • Dead load: (1) Slab = 50 psf, (2) Deck = 5 psf, (3) Mechanical equipment = 13 psf, (4) Suspended ceiling = 8 psf, (5) Beam = 25 Ib/ft, (6) Girder 35 lb/ft • Beam and Girder spacing: : (1) L1 = 14 ft, (2) L2 = 10 ft, (3) L3 = 10 ft Please round to the nearest one. Reaction force for Beam B-1 (one side only) = Ibs Reaction force for Beam B-2 (one side only) = Ibs Reaction force for Beam B-3 (open side) = Ibs Reaction force for Beam B-3 (Girder G-1 side) = Ibs MacBook Air II F8 F1 F2 F3 F4 F5 F6 F7 $ % & * 2 3 4 5 6 7 8 Beam B-1 Beam B-2 Beam B-3 Beam B-4 L3 L2
A rectangular concrete beam is 366 mm wide and 623 mm deep. It is reinforced at the bottom with 9-28 mm bars and at the top with 4-25 mm bars. Steel covering to bar centroid is 70 mm at the top and at the bottom of the beam. Use f’c = 25 MPa and fy = 415 MPa Determine the maximum factored load in kN/m the beam can support if it is simply supported over a span of 7.4 m and a 2.27-m overhang at both ends.
Use F = 50 ksi and select a shape for a typical floor beam AB. Assume that the floor slab provides continuous lateral support. The maximum permissible live load deflec- tion is L/180. The service dead loads consist of a 5-inch-thick reinforced-concrete floor slab (normal weight concrete), a partition load of 20 psf, and 10 psf to account for a suspended ceiling and mechanical equipment. The service live load is 65 psf. a. Use LRFD. -4 @ 6' = 24- 30′ a. W16X31 b. W16X45 c. W16X26 d. W16X77 e. W16X57 H -H
A T-beam for a floor system has a slab thickness of 75 mm and a web thickness of 375 mm. It has an effective depth of 600 mm. The beam carries a dead load moment of 280 kN-m and a live load moment of 525 kN-m. It has a span of 5.4 m and a spacing center to center of 1.8 m. Use reduction factor ø=0.90, fc’=20.7 MPa, fy = 344.7 MPa.Determine the effective width of flange. Determine depth of compression flange. Determine the required steel area. See the formula in the image
Example 3.7: Design the R.C beam of span and detail shown in Fig. below, to support the service load of (D.L= 25 KN/m not include beam weight, L.L= 10 KN/m). Use f'. =28 MPa and fy, = 420 MPa. D.L=25 KN/m, L.L= 10 kN/m 1; 7. 6000 mm fo—t
- Moodle English (en) A rectangular beam has a clear span of 18 ft long, is 12 in wide an effective depth of 20 in. Its supported a uniformly distributed dead load of 5.25 kips/ft and a live load of 4.75 kips/ft. Calculate the design shear at the critical section. Assume, f. = 4 ksi and fy = 60 ksi. W 5.25 k/ft W, = 4.75 k/ft 20 in 18 ft 12 in Select one: O a. 71.10 kips Ob. 92.80 kips Oc. 110.66 kips O d. 101.90 kips
A reinforced concrete beam 6m in length and 800 mmx 550mm in cross section is reinforced w/ 4-32 & bar supports and axle load of 50kN and 80kN on a wheel base of 3m. Using steel cover of 75mm, f'c = 28 MPa, fs=138 MPa. Let fc= 0.45 f'c. Find the Moment capacity of beam.
1. Determine the ultimate moment capacity of the T-beam shown below. The beam is reinforced with 6-032mm placed in two rows. Use fc=25MPA, fy=414MP.. 820 mm Il- 100 mm d= 610 mm 8 - 32 mn 250 mm 2. Determinethe safe concentrated live load at midspan that the doubly-reinforced beam section shown can carry if it has a simple span of 5m. Use f'c=21MPA, fy=276MPA, unit wt of concrete = 23.54KN/m³. 360 mm 2-0 25 mm Fď = 80 d= 680 mm 780 mm 8-0 36 mm 100 3. If in Prob. 2 the bottom bars are reduced to 6-032mm (3 in each row). Compute the safe concentrated live load at 1/3 span and 2/3 span the beam can carry.
If the beam is made from wood having an allowable shear stress tallow = 500 psi, determine the maximum magnitude of P. Set d = 5 in. |2P F211--2 ft-2 ft- 2 in.
Design an overhanging beam, given the following data.: fc' = 25 MPa; fs = 138 MPa ; n = 12. Use 25 mm diameter main bars and 12 mm diameter stirrups. PLL = 18KN 2m 6m WLL = 12 kN/m WDL = 18 kN/m
i Am set B pls asnwer