A rectangular beam of width 100 mm is subjected to maximum shear force of 60 kN. The corresponding maximum shear stress in the cross-section is 4 N/mm2. What is the ders of beam? (a) 150 mm (b) 225 mm (c) 200 mm (d) 100 mm

Q: Determine Iy and ky.

A: Solution: Compute the location of the centroid:   Area mm2 Xi , mm AXi larger Rectangle 1…

Q: 1. State the major ideas of RMR and Q system, and tell their differences. (

A: Rock Mass Rating system(RMR) is also known as Geomechanics Classification.

Q: e section are given by the table. The beam is subjected to the concentrate the couple moment Mo…

A:

Q: Can you explain why there is value of Iy. This figure the ly placed on the centroid, but correct me…

A: The solution of steel column capacity is given as above as per AISC Specifications. Now the question…

Q: If latitude of AB line is 40.96m an 50 m then what will be bearing of O 55 degree O 35 degree O o…

A:

Q: Can you explain how did you het Tab = 1160.695N, Tac...., Tad.....? Just go over equations for last…

A:

Q: り Iy= ? 「ん

A:

Q: Find the range of: f(x)=Vx+4.

A:

Q: (x+yc )dx - (xc ) dy こ0

A:

Q: Determine the centroid of the / ?figure presented in below 1.8 1n 1m1 2m 3m 2 2m 1m 0.5m X >X

A:

Q: 6. x + 4)x* - 4x + 2x? + 3x + 2 5. x+ 3)x* - 2x + 3x+ 4x – 1 er h Ginn 8. x+ 5)x - 2x + 3x? - 6x + 4…

A:

Q: Q1. Draw the plan and components of the given line diagram. Assume necessary any suitable data. W,…

A:

Q: Find the slope of the best fit line Concentration (g/100 mL) Hydrometer Height (mm) 0 20 4 35…

A: Slope of line or Best Fit line is the line which represents the direction and the steepness of line.…

Q: Consider the commercial steel pipe shown in (Figure 1). Determine the flow of methane at T = 68°F in…

A: Pressure Drop (ΔP) = 5 * 10^(-3) psiLength of the pipe (L) = 2600 ftDiameter of the pipe (D) = 1…

Q: A S 84 16'51" E B. D N 80°31'12" W ZA = %3D ZB = ZC = ZD = Next » S 3 27'40" E N 20°36'19" w

A: given question is from surveying we have to find interior angles of traverse

Q: Fore O, Rectangle, » Distance of Centroid fom x- axis, i-e, (7) A, = (42) (46 +19+21) = 3612 mm2 X,…

A: To Determine Volume using Pappus-Guldinus Theorem.

Q: A C L- (2) B "1-12- -L/2→ C x

A:

Q: What is the length of side "a" to the correct number of significant figures?

A: Given:- To find:- Length of side "a" Concept:- The rule of sines is a mathematical formula used in…

Q: -20 -0.5a 2a/3 T=0.5a

A:

Q: Compute for the following: 1. area of mid section between A1 and A2, A2 and A3, A3 and A4, A4 and…

A: Solution Area of section A2 Area A2 = A1+A2+A3+A4+A5 A1 = 12×2×2 = 2 m2 A2 = (2+4)2×2 = 6 m2 A3 =…

Q: ") FOR THE GIVEN SECTION. (DImensions ore in mm ) a) Determnine the location of neutral as from the…

A:

Q: What is the type of traverse shown in the picture? (select all that apply) Az Mk (a)

A: Given that:

Q: Name this force system         Question 19 options:   Non-planar parallel…

A: Given a system of force system

Q: LINES Line 1-2 Line 2-3 Line 3-4 Line 4-1 BEARINGS N 78° 07" E $10° 26' E $ 81°53' W N 10°05' W…

A:

Q: A wall has an area of 75 sq ft. Find to the nearer hundredth square meter thearea of the wall.

A: Given:- area = 75 sq ft To find:- Nearer hundredth square meter thearea of the wall.

Q: Which option is closer to the estimated size of a detention basin required to hold the runoff from a…

A: Given:- The return period of the basin = 10 yr The area of the catchment = 3000 ac To determine:-…

Q: ftware Orcad cadence in detail?

A: A schematic editor (Capture), an analog/mixed-signal circuit simulator (PSpice), and a PCB board…

Q: Determine AT

A: The expression for AT can be written as: AT=x4 × (y3 + y3) -12× x5 ×y3+12× x4 × y3  ⇒AT=12 ft × (4 +…

Q: 1. Ah = [ Select ] 2. Av [ Select ] 3. MA = [ Select ] %3D 4. C, = [Select ] 5. Dy = [ [ Select ] 50…

A:

Q: determine: a) the differential area b) centroid from x and y axis

A:

Q: 1/₂ B 1/₂ D 1/2. ( compute by and DD.

A:

Q: 9. Using cantilever method, determine the maximum absolute axial force in the column in kN due to…

A: Given data in question  Lateral loading Dimensions  Cantiler method  To find out  Axial forces in…

Q: Determine

A: Order of differential equation is defined as the highest order of the derivative occuring in the…

Q: TED 1. 6547 TED = 0-6043W (2)

A:

Q: B) Determine the order and degree of the following differential equation 1) y' + x?y = xe* 2) y" +…

A:

Q: 11. Which IS codes gives details about elevators? A. O IS 27752 B. O IS 38665 C. O IS 14665 D. O IS…

A: IS code that gives details about elevators

Q: Determine the location of centroid from x and y-axis.

A: To find centroid

Q: Q3 (a) Derive the ysat in terms of e, yw, and Gs

A: Question being asked here is to derive the formula for Saturated density of soil using the void…

Q: Draw according to scale. 12km, South 11mm,12\deg South of East 22(m)/(s),45\deg North of West 75cm,…

A:

Q: 2. S tanx.secx dx

A: using integration rules we can find value of given integration