A rectangular beam having a width of 250 mm has a total depth of 450 mm. It 0/1 is reinforced at the bottom with a total steel area of 1875 sq.mm. placed at an effective depth of 375 mm. fc'=27.6MPa and fy=414.7 MPa. If the beam has a simple span of 6m, determine the safe live load thet the beam could carry in addition to the dead load including its own weight of 20 kN/m? (Please answer in an encoded form for better understanding)

Q: A T-beam (internal) for a floor system has a slab thickness of 100mm and a total depth of 550mm. It…

A: T-Beam T-beams are constructed up of a flange and a rib in the shape of a T, and are usually built…

Q: A portal frame P Q R as shown in figure has a fixed support at P and free end at R. A point load of…

A: For a portal frame PQR as shown below,fixed support at P and free end at Rpoint load of 3 kN is…

Q: Design a reinforced concrete T beam. Use 55M concrete,f'c = 55 MPa; unit weight of concrete =…

A:

Q: 1- Design a rectangular section for the simply supported beam shown in the figure. The dead load wp…

A:

Q: 1- A W 5300*101 of Steel Section (f,= 345 MPa & fu= 450 MPa) is used as simply supported beam with a…

A: Given:W530×101Sx=2290×103mm3Zx=2620×103mm3Lb=3mmLp=1.94mLr=5,70mL=15mLp<Lb<LrLesser of either…

Q: Determine the location from the midspan in meters where stirrups are no longer required.

A: The values given in the question are as follows: Width of the beam(b)=300 mm The total depth of…

Q: 10 kN 6 kN/m 5 kN/m В 10 kN E 3 m 1.5 m--1.5 m--1.5 m-| CS CamScanner ile tarandı

A:

Q: Q3/ design a single simply supported beam with a is 18 kN/m and the live load is 12KN/m. Assume h…

A:

Q: A T-beam for a floor system has a slab thickness of 75 mm and a web thickness of 375 mm. It has an…

A:

Q: 2. Design the compression member in Problem 1 using W14 and A-50 steel. Use ASD with PDL= 990 KN AND…

A: Given, W14 , A50 steel PDL = 990 kN PLL = 680 kN

Q: quarter points. The maximum live load deflection must not exceed L/240 1 Q3- The beam shown in…

A: To Find Select a W shape section that can resist live load. Given concentrated load = 90 kN = 20.232…

Q: AW14 x 68 is used as a beam having a simple span of 6 m. Properties of WF Section. d = 356.62 mm %3D…

A: Answer We know that deflection for a simply supported beam carrying uniform load is given by…

Q: A rectangular beam has a width of 290mm, effectiv depth of 430mm, fc' = 26MPA, fy = 280MPa. Use 5-…

A:

Q: O . A

A: Which of the following is symmetric beam? option (b) is correct option

Q: The beam shown carries an ultimate load of 28.5 kN/m. The beam has a limited width of 275 mm and…

A: Ultimate load = 28.5 kN/m Width, b = 275 mm Height, h = 450 mm Reinforcement is placed at 65 mm from…

Q: Solve the problem below using method of section. Indicate if it’s compression or tension

A: Step 1: Step 2: Step 3:Step 4:

Q: Determine the maximum uniform load w that the beam can carry using A-36 steel. The lateral supports…

A:

Q: A 2L 70 x 7.38kg/m is used as a strut. It has a fixed support at the left end and a pin support at…

A: 2Lx70x7.38kg/m is used as a strut Span=5 m effective span=5/2 m or 5000/2, (one end is fixed and…

Q: A 3.0 m cantilever beam 360mm wide and having an effective depth of 520mm carries a service dead…

A: length of beam(L) = 3 mwidth of beam(b) = 360 mmeffective depth (d) = 520 mmdead load = 30 KN and…

Q: A steel beam of I cross-section is simply supported on a span of 4m. Find the safe uniformly…

A: Consider the free body diagram;

Q: An A36 W 12 x 65 column section is 8 m long, pinned at each end and has an additional support in the…

A:

Q: Design the beam shown below for shear, it is subjected to a service live load of 40 KN/m and a…

A:

Q: Q1: By the working stress method, Design the cantilever beam having length 4 m as shown below if the…

A:

Q: Q1: By the working stress method, Design the cantilever beam having length 4 m as shown below if the…

A:

Q: J 3 A simple T-beam with bf=600mm, h=500mm, hf=10mm, bw=300mm with a span of 3m, reinforced by…

A: Solution: Given: bf=600mm, h=500mm, hf=10mm, bw=300mm L = 3 m DL = 20kN/m  LL = 10 kN/m fc'=21Mpa,…

Q: 1 Example 3 Design a simply supported rectangular reinforced beam with tension steel only to carry a…

A: Design is as per ACI CODE 318

Q: Situation 2. A rectangular beam has b = 300 mm, d = 500 mm, As = 3 - 25 mm dia. RSB, f'c = 34.2 MPa,…

A: a = As * fy0.85 * fc' * b where ; As = 3 * π4(25)2 = 1472.02 mm2  fy = 414 MPa f'c = 34.2 b = 300 mm…

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A: Net power output =280 MW. Pressure ratio of the gas turbine cycle =11  Air enters the compressor at…

Q: A portal frame P Q R as shown in figure has a fixed support at P and free end at R. A point load of…

A: For a portal frame PQR as shown below,fixed support at P and free end at Rpoint load of 3 kN is…

Q: midpoint of the structure. The 275mm x 330mm (WxH) beam has the following properties: f’c = 29 MPa…

A:

Q: determine the ultimate moment capacity of rectangular beam whose width is 300 mm and an effective…

A: Given

Q: Design a T-beam for SHEAR, for a floor 75 mm thick. f=21 MPa, fy = 420 Mpa, fy = 300 MPa 'yt Wo=…

A: Answer Check for shear stirrups requirement Shear stirrups needed when Vu > ϕ.Vc2 Vu = critical…

Q: 3-3 A rectangular section with width b=200mm and depth h=450mm is reinforc with 4 16 of HRB400. The…

A: Width (b) = 200 mmDepth (h) = 450 mmReinforcement of concrete = 4 -16 diameter HRB400Design Moment…

Q: Q2 A simply supported beam of cross section 280X 560 overall depth. It spans over a length of 8.5 m.…

A: compression : The application of balanced inward forces to different places on a material or…

Q: A 5 m long simply supported beam carries a superimposed Iload of 20 kN/m. Design the midspan section…

A:

Q: G 67.5 kN 3.6 m -D -112.5 kN E 3.6 m IA B C 6 m +4.5 m Use portal method to analyze the frame.…

A:

Q: a) Find the factored critical moments based on ACI moment coefficients. b) Find Pmax c) Find pmin…

A: "Since you have posted a question with multiple sub-parts, the first three sub-parts will be only…

Q: Assignment 5.2 -Steel Beam Analysis P-20 kips P-? kips W 24 x 76 A992 Steel The beam carries the…

A:

Q: Girder AB. Assume Use Fy = 50 ksi and select a shape for that the floor slab provides continuous…

A:

Q: The beam AB is made of structural timber C24. The cross-section of the beam is rectangular with b x…

A: Beam AB:I=bh312=73(198)312I=4,72,21,218 mm4E=10,800 N/mm2EI=5.09 (1011) N.mm2 Cable:A=π4(10)2=78.54…

Q: Determine the force acting on members.

A: Step 1:For the given problem lets first eliminate the zero force member from the given truss,by…

Q: A W310×97 steel wide-flange section supports a uniformly distributed line load on a simple span of 4…

A:

Q: I

A:

Q: Beam and girder simplified analysis- FBD analysis including reactions. B2,B3,G2,G3. 100 psf total…

A:

Q: Situation A. The beam is loaded as shown 500 N 800 N 1.0m

A: As there are two different questions (methods) are posted, according to the guidelines, only the…

Q: Draw SFD and BMD for given loaded beam. 5 kN 10 kN ÎŢª 3 kN/m B 4 m 3 m 1 m C 3 m E D 1 m

A: Given:- To find:- Shear force and bending moment diagram

Q: ght is 15 kips/ft with Live load / Dead load ratio equals to 2. The beam is to be supported on RC…

A: According to given data  Bearing plate is design to distribute the reaction of W12x65 with a span…

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.