A rectangular beam has the following properties: bw = 300 mm d = 550 mm f'c = 21 MPa Stirrup diameter = 10 mm fyt = 276 MPa Determine the required spacing (in mm) of the vertical U-stirup when the required shear strength Vu is (a) 25 kN (b) 90 kN (c) 130 kN

A rectangular beam has the following properties: bw = 300 mm d = 550 mm f'c = 21 MPa Stirrup diameter = 10 mm fyt = 276 MPa Determine the required spacing (in mm) of the vertical U-stirup when the required shear strength Vu is (a) 25 kN (b) 90 kN (c) 130 kN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Мо В C A LAB LBC

Q: A reinforced concrete beam has a width of 425mm and an effective depth of 900mm. The longitudinal…

A: The given data is shown below: Width=425 mmEffective depth=900 mmCompresion…

Q: 100 N 350 N-m 2m 3m 2m

A: 1, FBD of beam is RA+RB=100Ntaking moment about A100×7-RB×5+350=0RB=210NRA=-110N for span ABSF at…

Q: For the beam with cross-section shown, the allowable flexural stresses for tension and compression…

A: TF1=20, BF1=3x20=60, Tw=20, Dw=8x20=160, TF2=20, BF2=10x20=200, D=a+8a+a=20+160+20 = 200

Q: Determine the safe span that a 100 * 150 mm purlin would have if it has a spacing 800 mm on centers,…

A: According to given data a 100 * 150 mm purlin if it has a spacing 800 mm on centersa roof load of…

Q: A rectangular beam has the following properties: fc'=28MPa fy=270MPa b=300mm d=450mm As=4 of…

Q: Below is a trapezoidal beam with 3-28mm reinforcing bars at the bottom. Using the design properties…

A: Given: fc = 21 MPa fy = 140 MPa n = 7 b1 = 200 mm b2 = 500 mm d = 650-50 mm Area of steel:…

Q: If M₂-465 kip-ft, find the magnitude of the bending stress at a point H. For the beam cross section,…

Q: A cantilever beam AB, loaded by a uniform load (see figure), is applied on a channel section. If the…

Q: The simply supported beam consists of a W530 x 66 structural steel wide-flange shape [E = 200 GPa;…

A: Given data: P=29 kn w=69 kn LAB=LBC=LCD=4.6 m LDE=2.3 m E=200 GPa I=351 *106 mm^4 It is asked to…

Q: PDL = 15 kN/m , PLL = 5 kN/m 2 - 16m 4m 5m 3m

Q: Q5- For the T-beam section shown below, calculate the cracking torque and check the section adequacy…

Q: 225 P,- 8 P,- 10 9- 18 2 (m) 1 (m) 4.50 (m) 1.50 (m)

Q: 1. Draw the shear and moment Diagram of the beam. 2. Determine the maximum compressive stress of the…

A: Given- A continuous beam of total span 12m and subjected to a UDL of 45Kn/m over the entire span.…

Q: Determine the minimum width "b" of the beam shown if the flexural stress is not to exceed 12 MPa.…

Q: Derive the relationship for maximum and minimum shear stress in a wide flange I-Section. Also…

A: Given: V=50KNflange width=300mmflange depth= 40mmweb thickness=40mmweb depth=220mm Calculate the…

Q: the design moment capacity of the beam

Q: H.WODraw the shear Stress distribution diagvam for the I-Section beam with unequal flanges shown in…

Q: property of the channel is given below: Depth, D = 225 mm Flange Thickness, t= 9mm Flange Width, B,…

Q: A triangular beam having a base width of 433 mm has a total depth of 776 mm. It is reinforced with…

Q: Situation 1 | An overhang beam is loaded as shown below. The beam cross-section was built by…

A: As per company's guidelines we can only answer first question Kindly post other questions as…

Q: Problem 2. 3m 3m 4m Hollow section p1 W b h t 38.0kN 12.1kN / m 164.0mm 264.0mm 7.5mm Determine the…

Q: A T- section is the cross section of a loaded beam as shown. Given: U1= 20 kN/m; M1 = 100 kN-m; P1 =…

Q: Question The span of cantilever beam is 2 m. The cross-section of the beam is a hollow square with…

A: A cantilever beam- span of the beam-L=2 m=2000 mm,sides of square=100 mm,Moment of inertia I=4×105…

Q: Situation 1 | An overhang beam is loaded as shown below. The beam cross-section was built by…

Q: Determine the maximum shearing stress on the beam in MPa. 8. Determine the flexural stress, in MPa,…

Q: For the beam shown below, draw bending stress distribution along the depth of beam at mid span…

A: Given that:

Q: 1. Determine the maximum shear W = 12 KN/m 4m 2m and moment of the beam loaded RI R2 shown.

A: Note: Hi! Thank you for the question As per the honour code, We’ll answer the first question since…

Q: 225 of 207 225

Q: Determine the minimum width "b" of the beam shown if the flexural stress is not to exceed 14 MPa.…

A: For the given beam and loading, the minimum width b has to be computed if the flexural stress is not…

Q: Determine the minimum width "b" of the beam shown if the flexural stress is not to exceed 13 MPa.…

Q: For the beam and loading shown, consider section n-n and determine the shearing stress at (a) Point…

A: Given:- To find:- Shear stress at point a Shear stress at point B Largest shear stress

Q: Determine the concentrated load at midspan that can be added if the uniformly distributed load ω is…

A: Given : Free Body Diagram (FBD) of Beam :

Q: Working stress design method 3/ By using the working stress design method find the maximum flexural…

A: Answer We know that stress in concrete is given by fc = M*ycIN.A And stress in steel is given by fs…

Q: thickness "t" of the steel plate if the

Q: Determine the maximum shear stress acting at section a-a of the beam below. 20 mm 4 kN 8 kN 70 mm…

Q: Determine the maximum bending stress of the following beam shown using the given cross-sectional…

A: To find Maximum bending stress?

Q: The simple bear with overhang carries a uniform load, w (k/m) and a force PKN). (a) Determine the…

Q: 15 mm PROBLEM 6.9 -250 mm 65 kN 90 kN 65 kN 0.3 m (300 пm) For the beam and loading shown, consider…

Q: (1)Calculate the maximum bending stress. (2)Compute the maximum web shear stress in MPa. (3)Compute…

Q: Design the steel reinforcement for the uniaxial eccentrically loaded short column shown below, using…

A: Given:- fc' = 28 MPa fy = 420 MPa ex = 150 mm Pn = 2200 Kn

Q: maximum flexural stress on the beam in MPa.

A: Given: Simply supported beam with a overhang carrying udl along its entire length. To determine: The…

Q: Below is a trapezoidal beam with 3-28mm reinforcing bars at the bottom. Using the design properties…

A: Given Data- A trapezoidal beam Reinforcing steel-3 bars, 28mm diameterfs=140MPafc'=21MPaeffective…

Question

A rectangular beam has the following properties:
bw = 300 mm
d = 550 mm
f'c = 21 MPa
Stirrup diameter = 10 mm
fyt = 276 MPa
Determine the required spacing (in mm) of the vertical U-stirup when the required shear strength Vu is
(a) 25 kN
(b) 90 kN
(c) 130 kN
(d) 290 kN
(e) 360 kN
(f) 570 KN

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Introduction

VIEW

Step 2 Calculation of spacing of reinforcement

VIEW

Step 3 Calculation for required spacing

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the positive nominal flexural strength Mn of the T-beam in the figure below. Assume fc′ = 21MPa and fy = 420MPa Determine the effective width of the flange if the clear spacing of the beams is 2m while the clear span length of the beam is 3m. Determine the Nominal Moment Capacity of the beam considering that the diameter of stirrup is 10mm and the concrete cover is at 40mm.
Title: Design of Beam in Flexure (WSD Method) PROBLEM: Design the beam to resist the loads shown. Take fc = 9 MPa, fs = 124 MPa, n = 11, bar diameter = 20 mm. Take b = d/2. Use WSD method. As (Gomm 20 KN lo Ka/m 8 KN/m 3m
1. For the given loaded beam shown, a. b. C. d. 40 kN-m B Im Im C 12 kN/m 3 m 2m E 125 -15- 15 145 Sketch the shear and moment diagram. Determine the maximum tensile bending stress in the beam. Ans. Determine the maximum compressive bending stress in the beam. Ans. Determine the maximum horizontal/transverse shear stress in the beam. Ans. dire lengt
In the following beam with the working section shown is subjected to the indicated loads and supported as shown, determine the magnitude of the twist BA and the deflection YC in the middle. Consider E = 70 GPa, A = 7.5 x 10-3 m2, IZ = 61.3 x 10-6 m4, IY = 23.2 x 10-6 m4 Develop by: 1) Double integration method 10 kN 2) Overlay Method 3) Moment area method 4m 4 m develop: a) Problem approach and solution sequence b) Free body diagram c) Calculation of intermediate and constant forces d) Bending moment diagram e) Application of equations and associated tables Caniatidado AM 141do earde tier ade
The simply supported beam consists of a W460 x 82 structural steel wide-flange shape [E = 200 GPa; I = 370 x 106 mm*). For the loading shown, determine the beam deflection vc at point C. Assume P = 56 kN, w = 22 kN/m, Lag = Lsc= 2.9 m, Lco = 2.9 m. LAB LBC LCD Answer: Vc= mm.
Please explain all options..
A T-shape beam is subjected to a vertical shear force of V = 30 kN. The beams centroid is located 211.1 mm above the bottom surface of the beam, and the moment of inertia is l₂ = 48.7 x 106mm4.[b = 178 mm, h = 300 mm, t₁ = 12.7, tw = 9] b h tw Determine the shear stress in the flange at the intersection of the flange and the web. 6.96 MPa 7.6 MPa 2.94 MPa 4.3 MPa 6.09 MPa
RUSH
3) Find the maximum shear stress. 4) Find the deflection midway between the supports. 4 kN/m 5 kN 1m 2 kN.m 2m 2m 2m 2m 5 mm E=200 GPA 20 mm 50 mm- Beam Cross-Section
Situation 11 An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets The property of the channel is given below: Depth, D=225 mm Flange Width, B=112.5 mm. Flange Thickness, tf=9mm Web Thickness, tw9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of t 100 MPa on shear, for bearing, o.-200 MPa on single sheer, a-260MPa on double shear. 2. Determine the moment of inertia, I, of the section in mm^4.
Q3 A compound beam consists of a standard I section 402 mm deep and 181 mm wide with a steel plate 200 x 25 mm deep welded to each flange. Given that the beam is simply supported over a length of 7 m, Ixx for the standard I section alone is 210.12 x 10°mm* and the maximum allowable bending stress is given in the table below, then: Allowable value of bending stress | 350 N/mm? (i) Sketch the cross section and calculate the second moment of area (Ixx) for the compound section. (ii) Calculate the maximum uniformly distributed load (UDL) the beam can carry if the flange plates extend over the whole 7 m span. (iii) Calculate the minimum central length over which the additional flange plates are required.