A rectangular beam has the following properties: bw 250, d = 475 mm, fc = 24 MPa, Stirrup Diameter dt 10mm, fyt 278 MPa. Determine the required spacing of vertical stirrup when the required shear strength Vu is equal to 38 kN.

A rectangular beam has the following properties: bw 250, d = 475 mm, fc = 24 MPa, Stirrup Diameter dt 10mm, fyt 278 MPa. Determine the required spacing of vertical stirrup when the required shear strength Vu is equal to 38 kN.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 5-4 Composite A-36 steel bar shown made from two segments AB and BD. Area AAB = 600 mm2 and Agp =…

Q: A reinforced concrete beam has the following properties: Beam width = 320 mm Effective depth = 640…

Q: Current Attempt in Progress A double tee cross section is used for the beam shown below. Assume the…

Q: SITUATION. A reinforced concrete beam 300 mm wide has a total depth of 650 mm. It is reinforced with…

Q: Below is a trapezoidal beam with 3-28mm reinforcing bars at the bottom. Using the design properties…

A: Given: fc = 21 MPa fy = 140 MPa n = 7 b1 = 200 mm b2 = 500 mm d = 650-50 mm Area of steel:…

Q: A horizontal tension member is to be constructed of two pieces of plastic glued along the incline pq…

Q: In the following beam with the working section shown is subjected to the indicated loads and…

Q: Determine the minimum width "b" of the beam shown if the flexural stress is not to exceed 13 MPa.…

Q: A 22.5 lb/ft ↓↓ 5.0 ft C 250 lb B 0.617 in. 2.269 in. Ⓡ -3.0 ft-

A: given- a cantilever beam carrying UDL and concentrated load and having maximum tensile stress 4ksi…

Q: Design rectangular section for the beam. Beam weight is included in the loads shown. Show sketch -f…

A: Given, Beam width (b) = 400 mm fy = 420 MPa f'c = 21 MPa

Q: Kindly give me right solution with clear calculations. P=7 KN UVL=48 KN/m E=200 GPa I=5.12x10…

A: Given, The beam is A Simply Supported Between Two Supports. The given Loading Arrangement on the…

Q: Current Attempt in Progress Two 4-in.-wide wooden boards are to be joined by splice plates that will…

Q: An exterior beam along with the Axis (A) between Axes (1) and (2) is part of monolithic floor system…

A: Uniformly distributed load=50 kN/m, Ultimate uniformly distributed torque=12 kN.m/m, Fc=28 Mpa,…

Q: H.W 1. For the cantilever reinforced concrete beam shown in Fig. loaded by ultimate uniform…

Q: property of the channel is given below: Depth, D = 225 mm Flange Thickness, t= 9mm Flange Width, B,…

Q: A simple beam of length L- 5 m carries a uniform load of intensity = 5.8 kN/m and a concentrated…

A: Given Data A simply supported beam is given with the following data Span length is 5 m A uniformly…

Q: A simply supported rectangular beam of length 6.45m has a width of 390.5mm and an effective depth of…

Q: Situation #3 A W 33x240 is used as a beam with length of cantilever beam equal to 8 m as shown.…

Q: the shear stress on the web at th he correct response: 4.66 MPa 20.94 MPa 27.04 MPa

A: Given that Shear V = 150 KN Shear stress at web in junction of flange and web= ?

Q: A rectangular beam with notches and a hole (seefigure) has dimensions h = 5.5 in., h1 = 5 in., and…

A: Given:- h=5.5in h1=5in b=1.6in M =130 kip-in σmax = 42,000 psi To find:- (a) What is the smallest…

Q: A 90mm concrete slab is supported by a beam 7.50m clear span and 1.20m on center. Web dimension and…

A: Given:- 90 mm concrete slabClear span=7.5 mDepth=500 mmWidth=300 mmfC'=21 MPaϕ=0.90Factored…

Q: Determine the maximum shearing stress on the beam in MPa. 8. Determine the flexural stress, in MPa,…

Q: Determine the minimum width "b" of the beam shown if the flexural stress is not to exceed 12 MPa.…

Q: shown if the flexural stress is not to exceed 13 MPa. Answer must be in mm. Given: a = 1 m, b = 3 m,…

Q: A floor system of a 100 mm concrete slab supported by continuous T Beam and has bw = 200mm, bf = 900…

A: Firstly, we need to determine how much reinforcement is needed for the T-beam to calculate A's. The…

Q: A rectangular beam has a width of 300mm and depth of 330 mm with a steel cover of 70 mm. Using…

Q: In reinforced beam having a width of 300 mm and an effective depth of 600 mm, carries a moment of 80…

A: This question is related to Design concrete structure. There is Option (A) 200 mm is correct answer.

Q: The 3-in. I beam shown in the figure below has cross-scctional properties of A - 1.64 in.". In= 2…

A: Given data A=1.64 in2 I11= 2 in 4 I22=0.46 in4 Sy= 42Ksi F.O.S =4 Unsupported length= 27.3 in

Q: by: e integration method 10 kN ay Method A nt area method

A: Hi! Thank you for the question As per the honour code, We’ll answer the first question since the…

Q: PROBLEM 5.2: A rectangular beam has the following properties: b = 350mm, d = 550mm. f = 21MPa,…

A: Given:- The width of the beam = 350 mm The depth of the beam = 550 mm The compressive strength of…

Q: 1.0. ZON m 17001/2 3 -1.01.mp

Q: Determine the minimum width "b" of the beam shown if the flexural stress is not to exceed 13 MPa.…

Q: A horizontal tension member is to be constructed of two pieces of plastic glued along the incline pq…

A: Given data, Inclination angle with horizontal = 30° Tensions stress = 5 Mpa Shear stress = 3 MPa…

Q: The four-span slab shown in the Figure 1 supports a variable action of 3.XkN/m² plus permanent…

Q: A simply supported beam has a rectangular section of b 65 cm and h 45 cm. The beam extends over a…

A: Span of beam (l) = 7 m The dimension of the beam, Thickness (h) = 450 mm Widht (b) = 650 mm…

Q: The pre stressed T-beam with a depth of 600mm is pre tensioned by a bonded pre stress tendon having…

A: Prestressed Beam: The term "prestressed concrete" refers to a type of concrete that is utilized in…

Q: Determine the minimum width "b" of the beam shown if the flexural stress is not to exceed 12 MPa.…

A: Given , total length of the beam =5m The beam is loaded with a udl of 3kn/m over the entire length…

Q: PROBLEM: Design the beam to resist the loads shown. Take fc = 9 MPa, fs = 124 MPa, n = 11, bar…

A: We have to design the beam according to the given data like Take fc=9 MPa, fs= 124 MPa, n = 11, bar…

Q: Compute the nominal compressive strength of a HSS 10 x 8 x 3/16. The length is 3.7m with one end…

Q: Determine the minimum width "b" of the beam shown if the flexural stress is not to exceed 11 MPa.…

Q: Below is a trapezoidal beam with 3-28mm reinforcing bars at the bottom. Using the design properties…

A: Given Data- A trapezoidal beam Reinforcing steel-3 bars, 28mm diameterfs=140MPafc'=21MPaeffective…

Q: Design the beam to resist the loads shown using WSD Method. Take fc = 9 MPa, fs = 124 MPa, n= 11,…

A: Solution Calculating Modular ratio m=2803σcbc=2803×9=10.370 calculating critical depth of neutral…

Q: 1. A rectangular reinforced concrete beam has the follawing properties: Beam Span, L 6 m Beam width,…

Q: Determine the minimum width "b" of the beam shown if the flexural stress is not to exceed 13 MPa.…

Concept explainers

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.

Question

100%

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the minimum width "b" of the beam shown if the flexural stress is not to exceed 14 MPa. Answer must be in mm. Given: a = 1 m, b = 3 m, c = 2 m, P = 6 kN, and w = 2 kN/m. am w kN/m R₁ PKN cm (not scaled) bm 260 mm
A simply supported rectangular beam of length 6.45m has a width of 390.5mm and an effective depth of610.5mm. The beam is to be reinforced using 12 ?? bars. The beam supports service dead loads ofWd = 13.5kN/m and WL = 35.5kN/m. f'c = 28Mpa and fy=420 MPa Given: b= 390.5 mm d= 610.5mm L= 6.45 m Wd = 13.5 kN/m WL = 35.5 kN/m 1. Calculate the ultimate moment capacity of the beam.2. Calculate the height of the equivalent stress block.3. Determine the number of bars required for this beam.
Determine the minimum width "b" of the beam shown if the flexural stress is not to exceed 14 MPa. Answer must be in mm. Given: a = 1 m, b = 3 m, c = 2 m, P = 7 kN, and w = 2 kN/m. P KN cm w kN/m (not scaled) 290 mm a m bm b Ri R2
Problem 2 A loaded cantilever beam is shown. E=29,000 ksi. The W16 section that will limit the total load deflection at the free end of the beam, B to 0.75 in. is most nearly: WD = 0.5 k/ft WL = 1.0 k/ft PD= 2 k B PL = 4 k Answer: W16 x L = 12 ft %3D
Determine the minimum width "b" of the beam shown if the flexural stress is not to exceed 12 MPa. Answer must be in mm. Given: a = 1 m, b- 4 m. c= 2 m, P- 6 kN, and w = 3 kN/m. P kN 上 cm w kN/m (not scaled) 240 mm, a m bm Ri R,
In the following beam with the working section shown is subjected to the indicated loads and supported as shown, determine the magnitude of the twist BA and the deflection YC in the middle. Consider E = 70 GPa, A = 7.5 x 10-3 m2, IZ = 61.3 x 10-6 m4, IY = 23.2 x 10-6 m4 Develop by: 1) Double integration method 10 kN 2) Overlay Method 3) Moment area method 4m 4 m develop: a) Problem approach and solution sequence b) Free body diagram c) Calculation of intermediate and constant forces d) Bending moment diagram e) Application of equations and associated tables Caniatidado AM 141do earde tier ade
Determine the minimum width "b" of the beam shown if the flexural stress is not to exceed 13 MPa. Answer must be in mm. Given: a = 1 m, b=4 m, c = 2 m, P=6 kN, and w 3 kN/m.
Please explain all options..
need asap please
Determine the minimum width "b" of the beam shown if the flexural stress is not to exceed 12 MPa. Answer must be in mm. Given: a = 1 m, b = 4 m, c = 2 m, P = 7 kN, and w = 4 kN/m. P KN cm w kN/m (not scaled) 270 mm bm a m R2 RI
Plz, solve this problem using Flexibility method and show all the steps one by one and draw SFD and BMD Structural Analysis-2
FN-01: ANALYSIS OF FLEXURAL MEMBERS Problem 01: Consider the beam loaded as shown and determine the following. Use Pn 10 x Class number + 50 kN. 1. The maximum bending moment 2. The maximum Shear 3. Maximum Deflection 4. Determine the bending coefficient. Show complete and orderly solution. w=5kN/m 1.50m 2Pn x marks are the location of lateral bracings 5.0m 3.0m