A rectangular beam has dimensions of 250 mm width and an effective depth of 430 mm. It is subjected to shear dead load of 102 kN and shear live load of 114 kN. Use f'c = 20.7 MPa and fyt = 276 MPa for 12 mm diameter U-stirrup. Design the required spacing of the shear reinforcement.

Q: Design the shear reinforcement for the concrete beam shown below. Note that the section width (b =…

A:

Q: A horizontal tension member is to be constructed of two pieces of plastic glued along the incline pq…

A:

Q: steel beam of I cross-section is simply supported on a span of 4m. Find the safe uniformly…

A: Given:- Span = 4m Simple Supported beam Tensile stress = 35N/mm2  To find:- w, δmax compressive

Q: Knowing that the bracket AB has a uniform thickness of t, Base of theory of elasticity, determine…

A:

Q: 4.16 (B). A reinforced concrete beam has to carry a bending moment of 100 kNm. The maximum…

A:

Q: Current Attempt in Progress Two 4-in.-wide wooden boards are to be joined by splice plates that will…

A:

Q: The beam shown carries an ultimate load of 28.5 kN/m. The beam has a limited width of 275 mm and…

A: Ultimate load = 28.5 kN/m Width, b = 275 mm Height, h = 450 mm Reinforcement is placed at 65 mm from…

Q: Design a rectangular beam to carry a live load of 1.5 kips/ft amd a dead load of 1.5 kips/ft, in…

A:

Q: A built up column section is composed of 2 C 310 x 45 and 2 plates b x 12 mm as shown in Figure ST –…

A: Properties of the given section are, Ixx=67.30×106 mm4Iyy= 2.12×106 mm4tf=12.7 mmx=17 mmbf=80…

Q: An exterior beam along with the Axis (A) between Axes (1) and (2) is part of monolithic floor system…

A: Uniformly distributed load=50 kN/m, Ultimate uniformly distributed torque=12 kN.m/m, Fc=28 Mpa,…

Q: A steel beam of I cross-section is simply supported on a span of 4m. Find the safe uniformly…

A: Consider the free body diagram;

Q: a) If olow 160 MPa, select the most economical metric wide- flange shape that should be used to…

A: Data given: σallow = 160 MPa Asked: Select most economical metric-wide flange shape Calculate Von…

Q: A simply supported rectangular beam of length 6.45m has a width of 390.5mm and an effective depth of…

A:

Q: P P – L - 6 in. (1) (2) 0.5 in.-

A: Given data: width = 6 in.

Q: The frame shown is subjected to lateral loads acting at I and E. Assume all columns have the same…

A:

Q: stress Oy in ksi). Both ctor of safety of FS = N te shear failure. De - See table to comp

A:

Q: What is the required minimum thickness (mm) of a 3.2m long, simply supported one-way slab if its…

A: Concrete slab The concrete block may be a current structural part gift in numerous buildings that…

Q: rete beam having a width of 250 mm, effective depth of 350 mm, and d’ = 65 mm is to be designed for…

A:

Q: The dimensions of a rectangular beam are limited to b - 300 mm and effective depth, d- 700 mm.…

A: Given data:- Width of rectangular bar, b = 300 mm Effective depth, d = 700 mm f'c=28 MPafy=415 Mpa…

Q: :Design the shear reinforcement for the beam shown below, kN W₂ = 200 f'c = 27.6Mpa, fy = 414Mpa,…

A: Solution

Q: A 13 150 mm

A:

Q: 3-3 A rectangular section with width b=200mm and depth h=450mm is reinforc with 4 16 of HRB400. The…

A: Width (b) = 200 mmDepth (h) = 450 mmReinforcement of concrete = 4 -16 diameter HRB400Design Moment…

Q: The given frame is unbraced, and bending is about the x axis of each member. The axial service loads…

A: Dead load (PD) = 908 KNLive load (PL) = 1816 KNYield strength (Fy) = 350 MPa  ≈ 50.76 ksiMoment of…

Q: Problem NO. 2. Determine the force acting on members HI, HJ, GI. Also, the force acting on members…

A:

Q: Calculate the ultimate moment capacity of the beam whose width is 400mm and effective depth d = 700.…

A: Given:Compression steel area=1953 mm2Tension steel area=4784 mm2Effective depth=700 mmwidth of the…

Q: Question 2: A compression member is subjected to service load of DL-180 KN and LL-335KN. The member…

A: Given:- The dead load on the column = 180 kN  The live load on the column = 335 kN  The length of…

Q: 2)The reinforced concrete beam has an effective span of 10 m and carries uniformly distributed dead…

A: Introduction- Steel and concrete beams are structural components designed to carry transverse…

Q: Q-2: A rectangular concrete beam of width, b= 32-inch is limited by architectural consideration to…

A:

Q: A horizontal tension member is to be constructed of two pieces of plastic glued along the incline pq…

A: Given data,  Inclination angle with horizontal = 30° Tensions stress = 5 Mpa Shear stress = 3 MPa…

Q: Rigid beam AB is supported by three bolts at A and a pin at B. The bolts at A are in double shear…

A:

Q: M=0.5kN.m A у P=2KN 5 KN m -0.25 1m 1.5m 0.75ml Choose an I-beam section that satisfies strength…

A: Given  σallowable = 22 MPA τallowable = 12 MPA ΣFy = 0 RA +RB = 2 + 0.25(0.75)            for UDL…

Q: A rectangular beam has a width of 300mm and an effective depth pf 537.50mm to the centroid of…

A: Given data,width of beam (b)=300mmeffective depth of beam (d)=537.50 mmf'c=27.6Mpa,Fy=414.7Mpasteel…

Q: Design the section below as a doubly reinforced beam for resisting the ultimate positive moment of…

A: We are given  Ultimate Positive Moment Mu = 425 KN-m We know that Nominal Moment capacity is given…

Q: gular beam has dimensions of 250 mm w hear live load of 114 kN. Use f'c = 20.7 MP ear reinforcement.

A:

Q: See the image below. A hot-rolled I-beam section has yield strength fy = 300 MPa, ultimate strength…

A:

Q: you don't know the solution please leave it but don't give me wrong solution

A:

Q: Determine the flexural capacity of the given section of beam below. b=400 d=575 d'=100 fc'=30 fy=345…

A:

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.