A receiving system consists of three components, an RF amp with 16dB power gain and Te = 35K, a mixer with 2dB power gain and Te = 40K, and an IF amp with 25dB power gain and Te = 52K. For a bandwidth of 1MHZ: a. What is the total noise power at the input of the RF amplifier 4.0434fW b. Determine the receiver's noise figure. 1.1257 c. Determine the receiver's equivalent temperature. 36.83K

A receiving system consists of three components, an RF amp with 16dB power gain and Te = 35K, a mixer with 2dB power gain and Te = 40K, and an IF amp with 25dB power gain and Te = 52K. For a bandwidth of 1MHZ: a. What is the total noise power at the input of the RF amplifier 4.0434fW b. Determine the receiver's noise figure. 1.1257 c. Determine the receiver's equivalent temperature. 36.83K

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

78. To assure the same accuracy at both 100 Hz and 100 MHz, the signal level into a frequency counter must be A higher at 100 MHz B. higher at 100 Hz C. inductively coupled at 100 MHz and capacitively coupled at 100 Hz D. resistively coupled at 100 MHz and direct coupled at 100 Hz
In a Frequency Modulator, the carrier signal, ec=8 sin[27(500k)t] is frequency modulated by em=5cos[2n(1k)t]). The Frequency deviation constant of the modulator is K= - 800 Hz/V. Determine: a. Frequency deviation at t=145µsec b. Frequency deviation at t-360usec c. Maximum frequency deviation d. Modulation index of the FM signal e. Equation of the modulated signal f. Instantaneous frequency of the FM signal at t=283usec g. The percent modulation if the modulated signal is for FM broadcast
Q. Choose the correct answer (.. 1. increases as the length of channel increases. (interference, distortion, additive noise, attenuation). 2. 100% modulation is produced in AM when carrier frequency exceeds signal frequency, amplitude equals signal amplitude, amplitude exceeds signal amplitude). 3. A 10 MHz carrier of peak value of 10 V is amplitude modulated by a 10 kHz signal of amplitude 5 V. The amplitude of each sideband frequency is 4. A Phase-Locked Loop (PLL) is a feedback circuit consisting of VCO, all of the above). 5. The line connecting the positive and negative peaks of the carrier waveform is called (Peak line, Maximum amplitude, Modulation index, Envelope) 6. Thermal noise power is proportional to (T², 1/T, T, T'2) 7. Which of the following is an advantage of SSB over DSB? (No change in spectrum space, Reduce in spectrum space, Carrier is suppressed, Power is not wasted on the carrier). 8. Which one of the following is not true with respect to SSB signal? (Hard to…
D E F
Determine the noise figure improvement for a receiver with an RF bandwidth equal to 500 kHz and an IF bandwith equal to 10 kHz.
An audio signal given by 15 sin(4000ntt) + 20 sin(8000mt) amplitude modulated(DSB-FC) a sinusoidal carrier wave 60 sin(100,000nt) a. Derive an expression for the modulated signal. b. Find the modulation index. c. Find the spectrum of the modulated signal. d. Sketch the spectrum of the modulated signal e. Which type of demodulation method you propose to reconstruct the audio at receiver. Why?
all 4
1. The CT signal x(1)-6cos (800zt) + 8cos² (mæt) is eritically sampled (Nyquist rate) by f-8000 Hz. Find: i. The value of m. ii. The frequency components of the signal. The frequency resolution (A) of the output spectrum if the sampled signal is processed by 32point-DFT. iii. iv. Define frequency resolution.
Provide a simple sample problem with correct solution regarding practical bandwidth calculation for frequency modulation (FM).
Q1): Use the PCM method to convert the signal below into a digital signal by assuming fm = 1000 Hz and n- 3. 4 -5 0.5 1 1.5 2.5 3 3.5 4 4.5 5 Time(ms) Q2): Use the DPCM method to: 1. convert the signal below into a digital signal by assuming fm = 500 Hz and n = 3. 2. reconstruct discrete signal at the receiver end. 3. calculate the error between the sampled discrete signal at transmitter end and the reconstructed discrete signal at the receiver end. 3 2 -2 3 2 3 4 5 10 1, (HOA) apnadury Amplitude (volt)
I need the answer as soon as possible
A Superheterodyne receiver is to tune the range from 1MHz to 3.6MHz, with an IFof 500kHz. The local oscillator frequency is always higher than the incoming RFsignals. a. Determine the capacitance tuning ratio of the variable capacitor of theRF circuitb. Determine the capacitance tuning ratio of the variable capacitor of thelocal oscillator circuitc. Calculate the frequency of the local oscillator if the receiver is tuned to3MHZd. Calculate the image frequency of 3MHze. Calculate the Image Frequency Rejection Ratio (in dB) of the receiver if itis tuned to 3MHz and the F filter selectivity is 100