a) Reason what the diagram looks like and identify each part. b) At what temperature will the mixture start to boil? What will be the composition of the steam at that time? c) What is the amount of distillate at 130C°? 160

a) Reason what the diagram looks like and identify each part. b) At what temperature will the mixture start to boil? What will be the composition of the steam at that time? c) What is the amount of distillate at 130C°? 160

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Shown to the right is the solid-liquid phase behavior for mixtures of component A and component B at 1 atm. Use the phase diagram to answer the following questions. a) Specify the melting point of substance B at 1 atm b) What is the maximum composition (mole fraction) of component B that is possible for the mixture to exist in phase S2? At what temperature does this occur? c) 20mol of component A and 180mol of component B are mixed at 350°C and 1 atm. The mixture is cooled at constant pressure to 200°C. i) What phases are present at the final state? ii) What is the composition of each phase at the final state? iii) What is the number of moles of each phase at the final state?
1. four processes. 2. Fill out the blanks by labeling the phase regions. 3. Identify the Indicate an in- termediate compound, if any. 3. Temperature (°C) 1600 1400 1200 1000 800 600 400 1538°C 0 (Fe) -1493°C 1394°C 912°C y, Austenite 1 2 0.16 5 0,022 a, Ferrite A N 2.14 Composition (at% C) 15 10 3 1147°C L4 3 4 Composition (wt% C) 4.30 727°C Sketch the microstructure at A, label phases, figure out compositions. 20 Cementite (Fe3C). 5 6 25 6.70
What variable/s play a role in determining how and when phase transitions happen? (Check all that apply) Properties of the Material/Substance Pressure Temperature
100 atm 1 atm 0.118 atm 114 °C 184 °C 535 °C Temperature (not to scale) a.) Use the above generic phase diagram, clearly identify where you would find the following: Gas, Liquid, Solid, Triple Point, Draw arrows and label to indicate the six transitions (melting, freezing, sublimation, deposition, vaporization and condensation) b.) Based on the above phase diagram, what phase would you be in at a pressure of 50 atm and 300°C? c.) Based on the above phase diagram at what temperature in °C would vaporization occur under normal conditions? d.) If the pressure was 0.050 atm and 425°C, what phase would you be in? e.) If the pressure was 0.118 atm and temperature was 114°C, what phase(s) would you be in? f.) At approximately what temperature would the normal freezing point be in °C? g.) If the pressure was 0.105 atm and starting at a temperature of 32°C to 450°C what phase changes would occur (put in increasing temperature order). Pressure (not to scale)
Assume that the following three phases are at equilibrium at the eutectic point. Which phase will have the highest solubility of Sn? Group of answer choices Beta Phase Alpha Phase Liquid Phase
If 20000 g of steam is condensed in 2 x 10^6 cm³ at a pressure of 4 MPa a. What is the temperature (C)? b. In what state steam? c. Draw it in the form of a phase diagram that you know
Determine the composition and fraction with 50% Ni and 1300 ° C
If 20000 g of steam is condensed in 2106 cm³ at a pressure of 6 MPa a. What is the temperature (C)? b. In what state (state) steam? c. Draw it in the form of a phase diagram that you know
how do you find the composition based on the tempratures from the phase diagram, like the temp are 160 and 130 right but you did both the temp above 150 in the phase diagram, also in the last line under given you wrote 35% sn and 55% sn, shouldn't it be 55% bi
Referring to Figure 1, please answer the following [NOTE: SHOW YOUR WORK on Figure 1]:a. provide the specific name for the phase boundary lines denoted by A and B. b. identify the phases present at equilibrium in the phase fields denoted by C, D, and E. c. identify the specific name for the point denoted by F. d. What is the maximum solid solubility of Mg in Al? At what temperature does it occur? e. An Al-Mg alloy (10 wt% Mg, 90 wt% Al) is heated slowly (to insure equilibrium) from a temperature of 200 C: i. At what temperature does the first liquid phase form? ii. What is the composition of the liquid phase at the temperature in part i.? iii. At what temperature does complete melting (no solid phase remaining) occur? iv. What is the composition of the last solid remaining prior to complete melting? f. Using the equilibrium phase diagram of Figure 1, identify the phases present, their compositions, and their relative mass fractions at equilibrium for a 70 wt% Mg – 30 wt% Al…
An alloy consisting of completely soluble cadmium (Cd) and zinc (Zn) in the liquid state, but neither of them dissolves in each other in the solid state. the table shown below shows the solidification temperatures for various alloys of cadmium and zinc. 1. Draw the equilibrium diagram according to the information given and data in the table and indicating all important temperature and phases. 2. Find the percentage of each phases and percentage of constituents of the alloy that contain 60 % Zn and at a temperature 300 °C. 3. Find the melting point for the following alloys 20 % Cd, 80% Cd 4. Draw the internal structure, noting the phases of the following alloys A) 30 % Cd at 290 °C b) 60 % Cd at room temperature. % of Zinc in alloy Start of solidification ("C) End of solidification ("C) 0 10 14 20 30 40 50 60 321 290 266 275 293 310 328 345 70 80 90 100 362 390 401 419 266 266 266 266 266 266 266 266 266 266 266 266
The point in the phase diagram where the fusion curve, the vapor pressure curve, and the sublimation curve join is called the Question 4 options: melting point. critical point. double point. boiling point. triple point. A sample of an ideal gas is slowly compressed to one-half its original volume with no change in temperature. What happens to the average speed of the molecules in the sample? Question 5 options: It doubles. It halves. cannot be determined without more information. It quadruples. It does not change. Phase changes occur Question 6 options: as the temperature decreases. all of the above. none of the above. as the temperature remains the same. as…