A Rarikine turbo-generator unit receives 27.300 kg/hr of steam at 6.6 MPaa and 500 C. Steam is extracted at 1.50 MPaa for fendwater heating. Condensate leaves at 16 kPa. Determine: (1) The amount of steam extracted, kg/hr (2) The total work of pump, kW (3) The cycle thermal etficiency, % (4) The engine thermal efficiency, % (5) The cycle steam rate, kg/kW-hr

A Rarikine turbo-generator unit receives 27.300 kg/hr of steam at 6.6 MPaa and 500 C. Steam is extracted at 1.50 MPaa for fendwater heating. Condensate leaves at 16 kPa. Determine: (1) The amount of steam extracted, kg/hr (2) The total work of pump, kW (3) The cycle thermal etficiency, % (4) The engine thermal efficiency, % (5) The cycle steam rate, kg/kW-hr

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Quickly, please.
An Actual Rankine cycle operates on a boiler and condenser pressure of 2MPa and 20kPa respectively. Steam leaves the boiler at 500C. Steam flows at a rate of 10kg/s in the cycle. The Turbine and Pump Efficiency are provided to be 87% and 89% respectively. a.) Determine the Heat Added to the boiler (kJ/s) b.) Determine the Work done by the pump (kJ/kg) c.) Determine the Thermal Efficiency of the Cycle (%) ROUND OFF ANSWER TO SIX SIGNIFICANT FIGURES
Hello, I would like to ask for your help in this problem. Also, Please show the complete solution clearly. Thank you very much
In an ideal Rankine cycle, steam is generated at 4.1 MPa and 480 deg. C. The condenser is at 32 deg. C. Determine: a. The cycle thermal efficiency b. For the engine with the same end states, the thermal efficiency and steam rate
Considering that the change in enthalpy at the first stage of a Reheat Rankine Cycle is 450 BTU/lb and 850 BTU/lb was recorded in the second stage, calculate for the thermal efficiency (in percent) of the cycle if both stages has a 93% efficiency and having a heat added of 9000 kJ/kg. (Hint: Neglect the pump work)
33 steam 14.0 MPa, 1100°C Generator Turbine 9.5 kPa Boiler H20 (in) H20 (out) Condenser liquid Pump For a Rankine engine operating between these limits, compute the thermal efficiency and the heat rate. b. Considering that a Rankine cycle occurs between the limits, determine QA, QR, WNet, and ec. What mass flow rate is required for a net output of 25 MW? a.
This is thermodynamics 2
Steam at 10 MPaa, 550 degrees celsius enters an ideal engine that has one stage of regenerative cycle; condenser pressure is 10kPaa and extraction of steam is at 1 MPa.
(a) A Steam power plant operates on a simple ideal Rankine cycle (Figure 2). Dctermine the thermal efficiency of this cycle when it is operated so that the liquid enters the pump as a saturated liquid. Boiler P- 6000 kPa I#O T-600 °C "pumpin Pump Turbine Condenser "pumpin Figure 2
Show the COMPLETE SOLUTIONS and DIAGRAM (T-s) (Cycle) including the switching of table and interpolations/extrapolations: NO Calculator Technique and Applications. Consider an ideal steam reheat cycle where steam enters the high-pressureturbine at 3.0 MPa, 400°C, and then expands to 0.8 MPa. It is then reheated to400°C and expands to 10 kPa in the low-pressure turbine. For the engine, find W and ec
! Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. The net work output and the thermal efficiency for the Carnot and the simple ideal Rankine cycles with steam as the working fluid are to be calculated and compared. Steam enters the turbine in both cases at 5 MPa as a saturated vapor, and the condenser pressure is 50 kPa. In the Rankine cycle, the condenser exit state is saturated liquid and, in the Carnot cycle, the boiler inlet state is saturated liquid. Draw the T-s diagrams for both cycles. (Please upload your response/solution using the controls below. You must provide an answer before moving on to the next part.)
|1) A steam power plant operates between a boiler pressure of 15 MPa and a condenser pressure of 5kPa. Calculate the maximum cycle efficiency.