A rapid mixing design basin is to be designed for a water coagulation plant and the design flow for the basin is 20,000 m3/day. The basin is to be square with depth equal to 1.25 times the width. The velocity gradient is to be 900/s at 10degrees Celsius, and the detention time is 30 seconds. Determine: The basin dimensions The input power required The impeller speed if vane disc impeller with six flat blades is employed and the tank is baffled. The impeller is to be 50% of the basin width

A rapid mixing design basin is to be designed for a water coagulation plant and the design flow for the basin is 20,000 m3/day. The basin is to be square with depth equal to 1.25 times the width. The velocity gradient is to be 900/s at 10degrees Celsius, and the detention time is 30 seconds. Determine: The basin dimensions The input power required The impeller speed if vane disc impeller with six flat blades is employed and the tank is baffled. The impeller is to be 50% of the basin width

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The ratio of the momentum correction factor to the energy correction factor for a laminar flow in a pipe IS (a) (c) N|W 2/3 (b) 1 (d) ½/12
A flow of water of 0.1 m³/sec flowing through rectangular tube of width 550 mm and having adjustable bottom slope with C = 55. Find the bottom slope required for uniform flow of depth 250 mm. Determine the convenience of %3D fume.
1) The horizontal flow toward drains causes an increase in the length of the flow lines, and consequently the hydraulic head losses increases because the higher velocity of the water flow near the drain. * O True False
A rapid-mixing basin is to be designed for a water coagulation plant, and the design flow for the basin is 15,140 m3/d. The basin is to be square with a depth equal to 1.25 times the width. The velocity gradient is to be 900 s-1 (at 10°C), and the detention time is 30s. Determine: a. The basin dimensions. b. The input power required. c. The impeller speed if a vane-disc impeller with six flat blades is employed and the tank is baffled. The impeller is to be 50% of the basin width. (use viscosity (u) = 0.0013 N-s/m²)
Q10.8 Hydraulic conductivity of an aquifer is known to be 8 ft/day, and its dimensions are estimated to be 40 ft thick and 18,000 ft wide. Two test wells drilled one mile apart in the direction of flow encountered the water table al clevations 5,030 t and 5,050 fL. Question: How many gallons of water flow through the aquifer per day? (To at the front of this manual.) o convert 'o gal, see page We've updated our read aloud featur Give it a try here. A Aa
ANSWER ASAP.
2. A water treatment plant serving a city of 300,000 capita with average water consumption 200 I/c/d. working period 20 hr./day. If R.T is 1 min and the depth of tank is 3 m, flash mixing tank 1. a. the diameter of the tank will be ... m
Chow, Ven Te, Handbook of Applied Hydrology, McGraw-Hill, 1964. FRICTION FACTOR f 08 07 Find the Q and V at the exit. Include friction losses (e.g., REAL fluid case) but ignore minor losses. Absolute Roughness e = 1.5 mm (See Moody Diagram next sheet) FE Manual Moody Diagram 06 .05 .04 03 02 01 0.1 0.2 CLAMINAR CRITICAL FLOW ZONE LAMINAR FLOW f-64/Re 0.4 0.6 0.8 1 6 8 10³ 2 TRANSITION ZONE CRITICAL Re 2 GLASS, DRAWN BRASS, COPPER, LEAD COMMERCIAL STEEL, WROUGHT IRON ASPHALTED CAST IRON GALVANIZED IRON CAST IRON CONCRETE RIVETED STEEL -0.03 CORRUGATED METAL PIPE -0.2 LARGE TUNNEL, CONCRETE OR STEEL LINED 0.002 -0.004 BLASTED ROCK TUNNEL 1.0 <-2.0 4 6 8 10 ZIN FI SMOOTH 410.0 feet 0.003 0.1 0.0001 -0.0003 0.0002 -0.0006 0.0002 -0.0008 0.0006 -0.003 0.001 -0.01 2 8" Dia. VALUE OF VD FOR WATER AT 60°F (V IN FPS, DIN INCHES) 4 6 8 10 2 4 6 8 10² 2 4 6 8 10³ 50' COMPLETE TURBULENCE ROUGH PIPES SMOOTH PIPES 4 6 8 105 2 4 6 8 10⁰ VD REYNOLDS NUMBER Re= V 2 3 00002 00001 6 8 10 372.5 feet 2 4 6…
A square rapid-mixing basin, with a depth of water equal to 2 times the width, is to be designed for a flow of 6530 m3/d. the velocity gradient is to be 700 mps/m, the detention time is 30 seconds, the operating temperature is 10ºC, and the turbine shaft speed is 100 rpm. Determine:a. The basin dimensionsb. The power required
HYDRAULICSFrom the figure shown, determine the flow in the open channel in cubic meter per second if the coefficient of discharge is 0.80NEED ASAP. PROVIDE COMNPLETE SOLUTION THANKS
A pneumatic mixing basin with a volume of 6200 ft3 is to be designed to provideG value of 60 sec-1. Assume that the basin depth is to be 12ft and air will bereleased into the basin 0,5ft above the tank bottom.(Temp= 60oF ) 2 5 ft 1bf.sec .2 359.10 − µ
o T ☺ ť Water flows in a channel whose bottom slope is 0.003 and whose cross section is shown in Fig. The dimensions and the Manning coefficients for the surfaces of different subsections are also given on the figure. Determine the flow rate through the channel and the effective Manning coefficient for the channel. Also calculate the freeboard and state the type of the flow (supercritical or suberitical) 8 m Clean natural Light brush channel 3m مر ر ل لأعلى لاستعراض الفلاتر إضافة شرح. . . mum <