A quantitative analysis for ethanol, C2H60, is accomplished by a redox back titration. Ethanol is oxidized to acetic acid, C2H402, using excess dichromate, Cr207 2-, which is reduced to Cr3+. The excess dichromate is titrated with Fe2+, giving Cr3+ and Fe3+ as products. In a typical analysis, a 5.00-mL sample of a brandy is diluted to 500 mL in a volumetric flask. A 10.00-mL sample is taken and the ethanol is removed by distillation and collected in 50.00 mL of an 2- acidified solution of 0.0200 M K2Cr207. Titration of the unreacted Cr207 requires 21.48 mL of 0.1014 M Fe2+. Calculate the %w/v ethanol in the brandy. Which is the titrant in this problem? O C2H4O2 O Fe2+ C2H60 Cr207 2-

A quantitative analysis for ethanol, C2H60, is accomplished by a redox back titration. Ethanol is oxidized to acetic acid, C2H402, using excess dichromate, Cr207 2-, which is reduced to Cr3+. The excess dichromate is titrated with Fe2+, giving Cr3+ and Fe3+ as products. In a typical analysis, a 5.00-mL sample of a brandy is diluted to 500 mL in a volumetric flask. A 10.00-mL sample is taken and the ethanol is removed by distillation and collected in 50.00 mL of an 2- acidified solution of 0.0200 M K2Cr207. Titration of the unreacted Cr207 requires 21.48 mL of 0.1014 M Fe2+. Calculate the %w/v ethanol in the brandy. Which is the titrant in this problem? O C2H4O2 O Fe2+ C2H60 Cr207 2-

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

In a lab, you diluted a sample of bleach to 1/10 concentration in a 250 volumetric flask. Then quantitatively transferred 25 ml of the 1/10 concentration diluted bleach into a beaker and titrated it with a standard sodium thiosulfate solution that has a molarity of 0.1215M. You repeated this 3 times. The data below is the amount of sodium thiosulfate that was titrated in the 3 runs. Calculate the molarity in each run of the diluted bleach and the concentration of undiluted bleach sample. Titration 1: 45.55 ml Titration 2: 45.67 ml Titration 6: 45.58 ml
One way in which the useful metal copper is produced is by dissolving the mineral azurite, which contains copper(II) carbonate, in concentrated sulfuric acid. The sulfuric acid reacts with the copper(II) carbonate to produce a blue solution of copper(II) sulfate. Scrap iron is then added to this solution, and pure copper metal precipitates out because of the following chemical reaction: Fe (s) + CuSO4 (aq) → Cu (s) + FeSO4 (aq)Suppose an industrial quality-control chemist analyzes a sample from a copper processing plant in the following way. He adds powdered iron to a 200.mL copper(II) sulfate sample from the plant until no more copper will precipitate. He then washes, dries, and weighs the precipitate, and finds that it has a mass of 73.mg . Calculate the original concentration of copper(II) sulfate in the sample. Be sure your answer has the correct number of significant digits.
One way in which the useful metal copper is produced is by dissolving the mineral azurite, which contains copper(II) carbonate, in concentrated sulfuric acid. The sulfuric acid reacts with the copper(II) carbonate to produce a blue solution of copper(II) sulfate. Scrap iron is then added to this solution, and pure copper metal precipitates out because of the following chemical reaction: Fe(s) + CuSO4(aq) → Cu(s) + FeSO4 (aq) Suppose an industrial quality-control chemist analyzes a sample from a copper processing plant in the following way. He adds powdered iron to a 350. mL copper(II) sulfate sample from the plant until no more copper will precipitate. He then washes, dries, and weighs the precipitate, and finds that it has a mass of 111. mg. Calculate the original concentration of copper(II) sulfate in the sample. Be sure your answer has the correct number of significant digits. 0-2 X 5
A 65.0 mL sample of a 0.110 M potassium sulfate solution is mixed with 36.5 mL of a 0.114 M lead(II) acetate solution and the following precipitation reaction occurs: K2SO4(aq)+Pb(C2H3O2)2(aq)→2KC2H3O2(aq)+PbSO4(s) The solid PbSO4 is collected, dried, and found to have a mass of 1.01 g . Determine the limiting reactant, the theoretical yield, and the percent yield.
Many chemical compounds contain impurities. Crude potassium carbonate (K2CO3) obtained from the chemical supplier is assayed for purity in the following way: 8.450 g of crude potassium carbonate is weighed out into a flask and dissolved in water. The final volume was completed to 0.500 L with distilled water. 20.00 mL sample is taken from this solution and placed in a flask. Potassium carbonate is then titrated to the equivalence point with 17.80 mL of 0.2050 M HCl solution. What is the percent purity of potassium carbonate in this sample? K2CO3 + HCl  KCl + H2O + CO2
One way in which the useful metal copper is produced is by dissolving the mineral azurite, which contains copper(II) carbonate, in concentrated sulfuric acid. The sulfuric acid reacts with the copper(II) carbonate to produce a blue solution of copper(II) sulfate. Scrap iron is then added to this solution, and pure copper metal precipitates out because of the following chemical reaction: Fe (s) + CuSO4 (aq) → Cu (s) + FeSO4 (aq)Suppose an industrial quality-control chemist analyzes a sample from a copper processing plant in the following way. He adds powdered iron to a 300.mL copper(II) sulfate sample from the plant until no more copper will precipitate. He then washes, dries, and weighs the precipitate, and finds that it has a mass of 67.mg . Calculate the original concentration of copper(II) sulfate in the sample. Be sure your answer has the correct number of significant digits.
A chemistry student needs to standardize a fresh solution of sodium hydroxide. He carefully weighs out 86. mg of oxalic acid (H,C,04), a diprotic acid that can be purchased inexpensively in high purity, and dissolves it in 250. mL of distilled water. The student then titrates the oxalic acid solution with his sodium hydroxide solution. When the titration reaches the equivalence point, the student finds he has used 37.0 mL of sodium hydroxide solution. Calculate the molarity of the student's sodium hydroxide solution. Be sure your answer has the correct number of significant digits. x10
The zinc content of a 1.55 g ore sample was determined by dissolving the ore in HCl, which reacts with the zinc. The excess HCl is then neutralized with with NaOH. The reaction of HClHCl with Zn is shown. Zn(s)+2HCl(aq)⟶ZnCl2⁢(aq)+H2⁡(g) The ore was dissolved in 150 mL of 0.600 M HCl and the resulting solution was diluted to a total volume of 300 mL. A 20.0 mL aliquot of the final solution required 8.92 mL of 0.548 NaOH to neutralize the excess HCl. What is the mass percentage (%w/w) of Zn in the ore sample?
A chemistry student needs to standardize a fresh solution of sodium hydroxide. She carefully weighs out 287. mg of oxalic acid (H, C,04), a diprotic acid that can be purchased inexpensively in high purity, and dissolves it in 250. mL of distilled water. The student then titrates the oxalic acid solution with her sodium hydroxide solution. When the titration reaches the equivalence point, the student finds she has used 75.9 mL of sodium hydroxide solution. Calculate the molarity of the student's sodium hydroxide solution. Be sure your answer has the correct number of significant digits. ||M
A solution contains one or more of the following ions: Ag+, Ca2+, and Co2+. Lithium bromide is added to the solution and no precipitate forms. An excess of lithium sulfate is then added to the solution and a precipitate forms. The precipitate is filtered off and lithium phosphate is added to the remaining solution, producing a precipitate. Which ions are present in the original solution? Ag+ O Ca2+ O Co2+ Write a net ionic equation for the formation of the precipitate observed after the addition of lithium sulfate. Include physical states. net ionic equation: Write a net ionic equation for the formation of the precipitate observed after the addition of lithium phosphate. Include physical states. net ionic equation:
The zinc content of a 1.07 g ore sample was determined by dissolving the ore in HCl, which reacts with the zinc. The excess HC1 is then neutralized with with NaOH. The reaction of HC1 with Zn is shown. Zn(s) + 2 HCl(aq) → ZnCl₂ (aq) + H₂(g) The ore was dissolved in 150 mL of 0.600 M HCl, and the resulting solution was diluted to a total volume of 300 mL. A 20.0 mL aliquot of the final solution required 9.96 mL of 0.540 M NaOH to neutralize the excess HC1. What is the mass percentage (%w/w) of Zn in the ore sample? %W/W = % Zn
105 Chemistry I Laboratory Manual, 2017 Revision Questions: 1) What mass of KHP would you need in order to use 35.00 mL of 0.400M NAOH to titrate it?