(A) Q: Three boards are bolted together to form the beam section shown in figure. The (6 mm) bolts are spaced at a distance of 150 mm. If the shear force V acting on the cross section is 6 kN, determine (1) the allowable shear stress at the N.A. (2) the shear stress at the bolt. 100mm 200mm 100mm **** 5mm 10mm 5mm

(A) Q: Three boards are bolted together to form the beam section shown in figure. The (6 mm) bolts are spaced at a distance of 150 mm. If the shear force V acting on the cross section is 6 kN, determine (1) the allowable shear stress at the N.A. (2) the shear stress at the bolt. 100mm 200mm 100mm **** 5mm 10mm 5mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The internal shear force V at a certain section of an aluminum beam is 8.7 kN. If the beam has the cross section shown (assume a=44 mm, b=87 mm, tw=t=4 mm, d=88 mm), determine: (a) the shear stress ty at point H, which is located 44 mm above the bottom surface of the tee shape. (b) the maximum horizontal shear stress Tmax in the tee shape. bf H a Answers: (а) тн — i MPa. (Б) тmах — i MРа.
A shear force of V = 240 kN is applied to the box girder. (Figure 1) Figure Part A 9A= 28.82 Part B 200 mm B 90 mm μÅ LO 9B = 16.42 200 mm 10 mm. A μÅ C D 180 mm Determine the shear flow at point A. Express your answer to three significant figures and include the appropriate units. MPa 90 mm Submit Previous Answers Request Answer 100 mm 190 mm -10 mm X Incorrect; Try Again; 5 attempts remaining Enter your answer with a different unit type. Review a list of acceptable units. MPa Determine the shear flow at point B. Express your answer to three significant figures and include the appropriate units. ? Pocke Submit Previous Answers Request Answer 1 of 1 ? > Incorrect; Try Again; 5 attempts remaining Enter your answer with a different unit type. Review a list of acceptable units.
In the figure, the boards are connected by nails to form a beam. A shear force of V= 70 kN acts on the beam. The dimensions of the plates are given as L1=170 mm, L2=140 mm and the thickness t=15 mm. The shear strength of each nail is 20 kN.Accordingly, determine the maximum spacing (s distance) between the nails. (Enter your result without writing units in mm.)
The figure shows the cross-section of a beam that is composed of a wide-flanged structural profile, whose specification is indicated in the figure, and two steel plates, joined by means of screws, placed in pairs with a longitudinal separation of 20 cm . If the beam is subjected to a vertical shear force of 25 KN, determine the shear stress supported by each bolt in the topsheet. Please add the free diagram body.
A simply supported beam (i.e., with a pin support at point A and a roller support at point D) is subjected to the external loadings shown in the figure. The cross- soction is shown to the right of the beam. 10 IN 10 KN mm 10mm Determine the shear stress developed in the cross-section n-n at point E on the web, 2m S0mm
AT OVERHANG( NEED NEAT HANDWRITTEN SOLUTION ONLY OTHERWISE DOWNVOTE).
The extruded cross section is subjected to a shear force of V = 495 N. Dimensions of the cross section are b = 42 mm, d = 75 mm, and t = 3.0 mm. Determine: (a) the value of Q associated with point H, located at a = 13 mm above the lower surface of the cross section. (b) the magnitude of the horizontal shear stress at point H. (c) the magnitude of the maximum horizontal shear stress in the cross section. ((уp) H a b Answer: (a) QH = 6306 mm3 (b) TH = i 1.091744397 kPa (c) Tmax = 1.637227058 kPa
PROBLEM No.1 If the wood joint shown in the figure has width of 200 mm, determine the average shear stress developed along shear planes a - a and b - 6. 8KN 8KN 125 mm 150 mm
From the given figure below, determine the flexural stress of the beam at fixed end if it has a cross section of 150mm wide by 250mm deep. HA VA 0 1750 40 N/m 3m -420Nm B & Im 550 35 N -75Nm с + 0° 55'N 20N 20N 0° DAV-DIAG -20Nm M-DIAG
Q1 If the cross section shown in the figure has a shear stress of 300 Psi at point P (located 0.25 in below the top line), find the shear force on the cross section. Express your answer in scientific notation. %3D 0-25" 1 0.5"| 5.5" REFERUCE 1.5" y A=bh 1,-
For the cross-section shown in Figure 2, determine the location of the shear center (e = 100mm 10mm V 6mm 190mm Shear Center e 10mm Figure 2