A pump with a 25 cmrev and 1000 rpm supplies the following circuit. If the characteristios of the 50 cylinder are v-01 ms, piston diameter60mm, rod diameter- 25mm and friction factoe-2000 Nsm and the characteristics of the 100kg cylinder are v0.02 ms piston diameter diameter-30mm and friction factor-s00 Nsim. Determine the flow rate and pressure on each cylinder. wm, rod 100 kg 25cm locorem boky

A pump with a 25 cmrev and 1000 rpm supplies the following circuit. If the characteristios of the 50 cylinder are v-01 ms, piston diameter60mm, rod diameter- 25mm and friction factoe-2000 Nsm and the characteristics of the 100kg cylinder are v0.02 ms piston diameter diameter-30mm and friction factor-s00 Nsim. Determine the flow rate and pressure on each cylinder. wm, rod 100 kg 25cm locorem boky

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

BOOK: FLUID POWER, 3e, JAMES A. SULLIVAN PROBLEM: 14 - 10
A hydraulic vane pump running at 1800 rpm develops 2 L/s flow at 750 kPa. Volumetric efficiency is .85 and overall efficiency is 0.8. Determine the Theoretical Torque required, TT (N-m). (Hint: first calculate the mechanical efficiency and theoretical flow rate. Convert rpm to rad/s). O 9.41 N-m 8.85 N-m 9.35 N-m 9.62 N-m 8.80 N-m
I need the answer as soon as possible
- A centrifugal pump with an impeller diameter of 350mm and specific speed of 19.15 and requires 15 kW to discharge 2.4 m³ /min of water, and runs at 1800 rpm. Determine the discharge, head and power required when the pump runs at 2400 rpm. The same discharge could be obtained by altering the impeller diameter without changing the rotational speed for this case find the new diameter of the impeller the head and the power required.
B. Given: Cylinder Diameter = 95 mm Displacement Distance = 110 mm Pressure Ratio = 8.72 P1 = 145 Kpa T1 = 26 Degree Centigrade Mechanical Efficiency = 78% Solve: Suction Volume, Mass Flow Rate, Work Done and Shaft Power N = 1350 RPM
When designing an impeller for a centrifugal pump, you would consider the following materials attributes. [M ten waaler vir 'n sentrifugale pomp ontwerp, sal jy die volgende materiaal eienskappe in ag neem.] O A. creep strength and density O B. hardness and chemical composition O C. toughness and stiffness O D. hardness and thermal expansion
Problem-3: A centrifugal pump lifts water against a static head Az = EN m. The pipe setup has a constant diameter of 0.08 m, major losses in the suction side h, = EN3 m and in the discharge side hLD is 3 m. The pump impeller has a diameter of 0.15 m, exit width of 0.015 m, exit blade angle of 22° and speed of N = 20EN rpm. The hydraulic efficiency is 0.85. If the flow at the entrance is radial, find the discharge, pump head, atmospheric pressure Pat, Vapor pressure P, and maximum allowable height of the pump from the feeding tank water surface elevation if the pump is operating under T 25 °C at altitude H= 20EN m. %3D 0, = NPSHR/Hp =1.21×10³N = (P EN=62 Is-mx at-abs-P,)/Y-hLsT -0H, Pa-abs /Y = 10.33(1– 2.256x10-H)56 P,ly = e14.29-3985(T+233.4))
In an external gear pump, if the delivery rate is 30 cm/revolution, the prime mover's speed which is connected to the pump of with 2670 rpm,Determine The pump delivery in terms of litres per minute is
answer 2nd item only