A pump is tested in the laboratory and the following data were obtained:= 5 ft-lbfTorqueRotational speedInlet pressureOutlet pressureVelocity in the inlet lineHeight to inlet gageT1200 rpm10 psia= 28 psia= 8 ft/s2 ft5 ftP1P2V=Z1Height to outlet gage = z2Inlet flow line = 2-nominal schedule 40Outlet flow line =2-nominal schedule 40Fluid = watera) Determine the pump efficiency.b) Consult an actual pump catalog and select a pump for these conditions.

Torque = T = 5 ft lbf Rotational speed = 1200 rpm Inlet pressure = P1 10 psia Outlet pressure P2 =…

A pump is tested in the laboratory and the following data were obtained: Torque Rotational speed Inlet pressure Outlet pressure = 5 ft-lbf = 1200 rpm 10 psia 28 psia = 8 ft/s T = P1 P2 Velocity in the inlet line = V Height to inlet gage = 2 ft Z1 Height to outlet gage = z2 = 5 ft Inlet flow line = 2-nominal schedule 40 Outlet flow line = 2-nominal schedule 40 Fluid = water a) Determine the pump efficiency. b) Consult an actual pump catalog and select a pump for these conditions.

A pump is tested in the laboratory and the following data were obtained: Torque Rotational speed Inlet pressure Outlet pressure = 5 ft-lbf = 1200 rpm 10 psia 28 psia = 8 ft/s T = P1 P2 Velocity in the inlet line = V Height to inlet gage = 2 ft Z1 Height to outlet gage = z2 = 5 ft Inlet flow line = 2-nominal schedule 40 Outlet flow line = 2-nominal schedule 40 Fluid = water a) Determine the pump efficiency. b) Consult an actual pump catalog and select a pump for these conditions.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

QUESTION 3 The following conversion equivalents are given: 1 gal 231 in 1 ft 12 in 1 min 60 s A pipe delivers water at the rate of 51 gal/min. The rate in ft3/s, is closest to: 0.083 0.11 0.093 0.073 0.10
Given: A pipe connecting two reservoirs as shown in Fig. 1. Absolute roughness of both pipe sections is 0.5 mm. Calculate: a) Equivalent pipe loss coifficient b) Equivalent pipe length which can replace the secondary losses c) Discharge in the two pipes (ignore secondary losses) d) Equivalent pipe diameter required to replace the two pipes in series (Leq = 2500m) e) Sketch EGL ( solid line) and HGL (dash line) H= 50 m L = 1000 m 2000 m- %3D Water 20°C 70 m-t D= 200 mm Valve D =300 mm Figure 1 (Half closed)
B. Read are these sentences and choose the True or False. Answer only five 3-The Fluid friction apparatus in (major losses turbulent flows experiment) it is: h/ u V hoc u Log Ihl Where: h:the loss of head due to pipe friction. u :the velocity. 4- The Reynolds number is a ratio of an inertia force operation to a viscous force. Log lul
a) Develop an equation for the head (in ft) developed by the pump described by the chartas a function of flow rate (in gpm) when the pump uses a 9 ¾” impeller. b) Develop an equation for the pump efficiency as a function of flow rate (gpm) when the pump uses a 9 ¾” impeller.
1. Using the Steam Tables, determine the heat absorbed by the boiler (KW) and Wsf when subcooled water at pressure = 5 Mpaa (subcooled by 64 deg C measured at the boiler inlet), is superheated to 100 degrees SH at the same pressure. Flow rate is at 10 cubic meters per minute. Ans.: a) Qa = b)Wsf= Hint: Use v at compressed water temp. at boiler inlet to convert to mass flow rate. Process is isobaric (Constant Pressure, where Q=m x AH).
ENGINEERING HYDRAULICS
Show the solution and final answer in two decimal.
A) Calculate by hand the net head delivered and the efficiency of the pump at flow rate of 63 L/s. B) Use excel sheet and its formula to solve the equations and plot the pump head, power input, and efficiency versus the pump flow rate
Please solve the problem correctly and get the right answer.
A pipe has a cross-sectional area of 16.5cm2 at point A, where the speed of the fluid (water) is 1.2 m/s and the pressure is 2.00 atm. The pipe ascends 3.00 m and narrows to 8.20 cm2 at point C. a) what's the speed of the fluid at point C. b) what's the absolute pressure at point C.