A pump is discharging 12 liters/sec of water through 10 cm diameter pipe. When the pressure on the discharge side of the pump is 700 kPa, what pressure can be expected in the discharge pipe at a point 540 m distant from the pump and 45 m higher in elevation. Use n = 0.015

A pump is discharging 12 liters/sec of water through 10 cm diameter pipe. When the pressure on the discharge side of the pump is 700 kPa, what pressure can be expected in the discharge pipe at a point 540 m distant from the pump and 45 m higher in elevation. Use n = 0.015

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Answer seems to be 736kpa, please show Formula and calculation as fast as (handwritten only) A 75-m-high water body that is open to the atmosphere is available. Water is run through a turbine at a rate of 200 L/s at the bottom of the water body. The pressure difference across the turbine is
The water is flowing through a pipe having diameters 30 cm and 21 cm at sections land 2 respectively. The rate of flow through pipe is 40 litres/s. The section 1 is 7 m above datum and section 2 is 3 m above datum. If the pressure at section 1 is 37 N/cm? , find the following by neglecting losses: (ENTER ONLY THE VALUES BY REFERRING THE UNIT GIVEN IN BRACKETS) ) Area of cross section of section1 (unit in m?) = Area of cross section of section2 (unit in m?) = velocity at section 1 (unit in m/s) = velocity at section 2 (unit in m/s) = (ii) difference in datum head (Unit in m) = Pressure head at section 1 (Unit in m) = pressure head at section 2 (unit in m) =
I need the answer as soon as possible
A Pelton wheel develops 750 kW under ahead of 200 m. Its nozzle has a diameter of 10 cm and losses in the pipeline due to friction amount to 90 Qʻ, where Q is discharge in cubic meters per second. Assuming the gross head and efficiency of the wheel to be constant and Cy for the nozzle as 0.98. Find the discharge and overall efficiency. If the power developed is reduced to 650 kW by (i) Operating the needle in the nozzle and
Apply Bernoulli equation in solving the problem: A 3.81-cm diameter venturi meter is installed in a pipe with an internal diameter of 10.23 cm. A 127 cm manometer filled with mercury is used to measure the pressure difference across the venturi meter. If the manometer reads 101.6 cm when 15 °C water is flowing through the pipe, what is the flow rate of water (m3/min)? Assume that the venturi meter coefficient of discharge equals 0.98.
None
.
A pipe of diameter 18 cm, is used to pump the water to the house in the Hamra hill at the height of 50 m than the ground. The discharge at the end of the pipe is 220 lit/s. The pressure gauge is fitted at the entry of the pipe in the ground is 35 N/cm². Find the following: (i) The velocity head at the entry of pipe (in m) (ii) Pressure head at the inlet (in m) (iii) Total available energy per unit weight of the water at the pipe inlet (unit in m) (Enter only the values by referring to the units given in brackets & DO NOT write the unit & do not send the handwritten answers to my mail id....) velocity head at the entry of the pipe is = (unit in m) pressure head at inlet = (unit in m) Total available energy per unit weight of the water at inlet of the pipe (unit in m) ,
Write the expanded form of Darcy’s Law. Draw a tube full of sand, with piezometers, and label the components of the system.
A pumping station wet well operates between 540- and 550-ft elevation. The pump curve is deϐined by the following points: 80 ft at zero ϐlow, 78 ft at 200 gpm, 65 ft at 800 gpm, and 50 ft at 1200 gpm. The pump discharge contains an equivalent of 50 ft of 6-in. pipe. The discharge pipe is 120-ft long and terminates at a splitter box, elevation 570. Using C=100, plot the pump curve and the corrected pump curve. Plot the pump discharge curves at each wet well elevation and for C=100 and C=140. What is the pump ϐlow at the low and high wet well elevations for newand old pipe?
The task is to to transfer the fluid from the source towards the tank (TANK A) lying on an elevated platform as shown. The goal is to fill up that 16.49 m by 2.23 m by 6.36 m tank (TANK A) within 11.5 mins (from empty to full). Your budget is limited to 605,000 pesos. Head loss on pipe due to friction is 1.23 meters per 1 meter of pipe. Because it's Fluid Machinery and not Engineering Economics, it's ok for your design to exceed the budget BUT YOU HAVE TO JUSTIFY IT. The pictures I will post is the guide to answer Its okay if the answer is computerized
A balloon is being filled with water at an instant when the diameter is 50 cm. If the flow rate into the balloon is 200gal/min, what is the rate of increase in the diameter?