A pump draws water from an 8 in. suction pipe and discharges through a 6 in. pipe in which the velocity is 12 fps. The pressure is –5 psi at point 1 in the suction. The 6 in. pipe discharges horizontally into the air. The power delivered to the pump is 30hp whose efficiency is 70. Determine: a. the water horsepower 21 18 15     b. the total dynamic head in feet 94.316 78.564 67.369     c. To what height h in feet above the suction gage can the water be raised? 81.716 65.498 54.303   please answer immediately thankyou

Q: What is the flow rate of water through the system shown for the turbine to produce 20 kW. Neglect…

A: Given Data  Height, h= 30m   density =1000 Kg/m3.

Q: 15. A pump operating at 660 hp delivers water, from a large pressurized supply tank to a large…

A: Given: The pump power, P = 660 hp The water flow rate, Q = 150 ft^3/s The total length, H = 1000 ft…

Q: Question Two ( A three stage C.P. has impellers (Pcm) in diameter and (1.8cm) wide at outlet. The…

A: A three stage C.P. No of stage = 3 Diameter of outlet D2= 40 cm =0.4 m Width pof outlet B2 = 0.018m…

Q: An axial flow turbine operates with a constant axial velocity throughout of 230. The rotation speed…

A: Given Data: V=230 m/sN=3600 rpmr=1.2 mθ=35o   To Find: (a) Velocity triangle at the inlet and exit.

Q: The impeller of a centrifugal pump is 0.5 m in diameter and rotates at 1200 r .p. m . ; blades are…

A: Given, D = 0.5 m N = 1200 RPM Flow Velocity at Exit, Vf2 = 5 m/sec For Blade Velocity, u u =…

Q: A centrifugal pump is used to lift water from a water reservoir with level 1 m below the pump center…

A:

Q: The system in Fig 2 pumps water from a lower reservoir to a higher reservoir.  The pipe diameter is…

A: Given That: Pipe diameter dp= 0.235 m,L1=5 m, L2=4.5 m, L3=1.5 m, L4=0.6 m,impeller diameter d =…

Q: A Francis turbine develops 500 kW at 500 rpm under a head of 50 m. The hydraulic efficiency is 95%…

A:

Q: Find the loss in total pressure for each run in the simple duct system of Fig. 1, using the…

A:

Q: /A Pelton wheel has a tangential velocity of buckets of 15 meters/sec. the water is being supplied…

A: calculated the power produced by the wheel in watts.

Q: A certain hydro-power station has a head of 500m between the upper and lower reservoir . a.…

A: GivenH=500mPart aV2=?Part bQ=60  m3/s d=?Part chL=10%V2'=?d'=?

Q: A large container filled with water and uncovered for use in fighting fires in an ethylene…

A:

Q: B/A pump operates at 17237.5 kPa, discharges 11.4 liter/min and requires a pow 3.75 kW to drive the…

A: Given Pressure P=17237.5kPadischage rate Q=11.4 ltr /min=0.0114 m3/min=0.011460 m3/sspeed N=1725…

Q: 2. A sump pump turning at 1600 rpm provides a water discharge of 9gpm againts a head of 18ft.…

A: The fundamental rule of activity of divergent siphons is - force vortex stream. This implies, when a…

Q: For pumping a liquid refrigerant with a density of 1226 kg / m3 D1 = 200 mm, D2 = 360 mm, b1 = 50…

A:

Q: the blades due to friction. Taking the blade angles at the inlet and outlet to be equal, find the…

A:

Q: station, there is a centrifugal pump. The pump delivers a flow rate of 0.003 m3/s. The pump radius…

A:

Q: A Kaplan Turbine develops 5000 kW under the net head of 5 m. The speed ratio and flow rat are 2 and…

A: P=5000kWH=5mSpeed-Ratio=2Flow-ratio=0.5ηo=0.92Do=3Db To-Find:- Speed

Q: the buckets. The speed factor is 0.46. Neglecting any losses, determine: 360 m. The wheel is driven…

A: Introduction: The Pelton turbine operates on a basic basis. When a high-speed water jet shot by a…

Q: Q.21 Water is being pumped at a rate of 0.5 ft/sec from a storage tank to a certain exit point of…

A: For solution refer below images.

Q: A three stage C.P. has impellers (cm) in diameter and (1.8cm) wide at outlet. The vanes are curved…

A:

Q: The impeller of a centrifugal pump has an internal diameter of 200 mm and external diameter 400 mm.…

A: Centrifugal pump Centrifugal pump works on the principle of forced vortex that means liquid is…

Q: e power required to drive t e pump.

A: Need to find the power required to drive the pump.

Q: A centrifugal pump supplies water at the rate of 750 liter/s against manometric head of 15 m of…

A:

Q: A centrifugal pump has an impeller of diameter 250 mm whose width at the exit is 50 mm. The flow…

A: Given data: Write the expression to calculate the discharge.

Q: This course CHide block A centrifugal pump with the following impeller dimensions is used to pump…

A:

Q: Q8: A form stage centrifugal pump running at 600 rpm is to deliver 1 m'/s of water against a…

A:

Q: Centrifugal pump impeller runs at 950 rpm. Its external and internal diameters are 500 mm and 250…

A: Given: The speed of impeller, N = 950 rpm The external diameter of impeller, D = 500 mm The internal…

Q: A Kaplan turbine of 100 B.H.P. is working under a head of 5 in and running at 210 R.P.M. The…

A:

Q: The pump has an er diameter of 8 cr 1750

A: The outer diameter of the pump is .The inner diameter of the pump is .The width of the blade is .The…

Q: The velocity of water and pressure at the suction side of a pump is 4m/s and 90kPa respectively. If…

A:

Q: radial bladed centrifugal pump running at 1440 rpm is to deliver 30 l/min of water against a  head…

A:

Q: A Pelton wheel has a mean bucket speed of 10 meters per second with a jet of water flowing at a rate…

A:

Q: 18. A centrifugal pump has, to work against a head of 25 metres at a speed of 850 rpm.. The flow…

A: Given data: Head against which pump is working, Hm=25 m. Speed of the rotor, N=850 rpm. Flow…

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.