A power screw with double start ASME thread is proposed to be used for (Q1)cyclically raise and lower a load of 1000 Ib at an axial velocity of 4 in/sec. It hasthree threads per inch and with thread outside diameter of 1.50 inches. Theproposed mean collar radius is 1 inch. The starting and sliding frictioncoefficients for the screw and the collar are f_starting=0.06 and f_running=D0.03find: a. The staring and the sliding torque required to raise the load.b. Check theself-locking condition for the screw assembly. c. What is the power screwefficiency of the proposed assembly?d. If a special gear motor is to be used todrive this power screw assembly, what would be the minimum power and torquerequirements for the drive motor?e. The length of the nut if the permissible.bearing pressure is 725psi

Answered: Image /qna-images/answer/a9389549-9ecb-4437-9cf3-2053130fca72.jpg

A power screw with double start ASME thread is proposed to be used for (Q1) cyclically raise and lower a load of 1000 Ib at an axial velocity of 4 in/sec. It has three threads per inch and with thread outside diameter of 1.50 inches. The proposed mean collar radius is 1 inch. The starting and sliding friction coefficients for the screw and the collar are f_starting=D0.06 and f_running=0.03 find: a. The staring and the sliding torque required to raise the load.b. Check the self-locking condition for the screw assembly. c. What is the power screw efficiency of the proposed assembly?d. If a special gear motor is to be used to drive this power screw assembly, what would be the minimum power and torque requirements for the drive motor?e. The length of the nut if the permissible bearing pressure is 725psi

A power screw with double start ASME thread is proposed to be used for (Q1) cyclically raise and lower a load of 1000 Ib at an axial velocity of 4 in/sec. It has three threads per inch and with thread outside diameter of 1.50 inches. The proposed mean collar radius is 1 inch. The starting and sliding friction coefficients for the screw and the collar are f_starting=D0.06 and f_running=0.03 find: a. The staring and the sliding torque required to raise the load.b. Check the self-locking condition for the screw assembly. c. What is the power screw efficiency of the proposed assembly?d. If a special gear motor is to be used to drive this power screw assembly, what would be the minimum power and torque requirements for the drive motor?e. The length of the nut if the permissible bearing pressure is 725psi

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

a. Does the slip increase as the load increases? What is the reason of this? b. What does it mean if the shift is 0, 1, -1, how is it achieved? Explain.
8) the armature resistance of dc machines with number of poles > 2 is larger when the machine is: wave wound lap wound None of the above
What is the significance of fault analysis in power systems, and how is fault location determined?
i need it asap
A 500-turn coil is wound on an iron core. When a 120-V-rms 60-Hz voltage is applied to the coil, the current is 1 A rms. Neglect the resistance of the coil. Determine the reluctance of the core. Given that the cross-sectional area of the core is 5 cm2 and the length is 20 cm, determine the relative permeability of the core material.
ii) An emf, 2.5kV induced in a coil when a current of 2.75A collapses uniformly to 1.7SA in 4ms. Determine the flux induced in the coil in Webber-turns.
please ans A B AND C FOR ME. PLEASE DO YOUR BEST WITH HIGH ACCURACY
What is use of solenoid coil in the pressure to converter? a. To produce magnetic field in the LVDT b. To change the LVDT output c. To bring back the pivoted beam normal position d. To produce linear displacement in bellows
A flux of 0.0016 Wb flows in a silicon sheet steel coil/core. The arrangement appears as shown below with the following dimensions: Ac = 0.0025 m? Core/gap area: Flux path length: le = 0.350 m lg = 0.0015 m N = 500 Air gap length: Number of turns: %3D A. What is the current, I, through the winding? B. What is the energy stored in the inductance? C. Assume that the current is given by i =9.75 sin (3147) A. What is the RMS voltage that would appear across the winding? D. Assume that the gap is removed from the arrangement with the flux path remaining at 0.350 m. For a flux of 0.0016 Wb, what is the inductance of the arrangement? E. What is the energy stored in the inductance with the gap removed?
An electromagnet has a movable iron part and dimensions of magnetic circuit with uniform cross section as shown in figure. The core is made of ferromagnetic material with relative permeability of 3000: a) b) c) Calculate the magnetic reluctance of the circuit and the inductance of the main winding. Determine the air-gap flux, the flux density and the field intensity of the core and gap. Because of a fault in the power supply, the exciting current is increased to 8 A causing the mobile element of the iron core to move to a zero gap position as a result of the excessive electromagnetic force action. If this movement occurs in 0.01 s, find the transient voltage induced in the test coil having two turns. 0.5 mm air-gap 2 cm 2 A 3 cm 2 cm 60 turns 18 cm test coil 24 cm 0.5 mm air-gap
Q3) In a two-excitation and two-pole machine, the rotor and stator of both poles are prominent relations The inductor of the rotor and stator is as follows: Lss =(0.5 + 0.2cos20) H Lrr =(0.8 + 0.3cos20) H Lsr =0.7coseH The resistance of the windings is zero. If the rotor is in the position 0 =60 ° and flows from the stator A sinusoid with an effective value of 10A passes and the rotor winding is short, medium torque Calculate the impact on the rotor
An air-cored choke is designed to have an inductance of 20H when operating at a flux density of I Wb/m²: the corresponding relative permeability of iron core is 4000. Determine the number of turns in the winding: given that the flux path has a mean length of 22 cm in the iron core and I mm in air gap and that its cross-section is 10 cm².