A power plant operates on a regenerative vapor power cycle with one open feedwater heater. Steam enters the first turbine stage at 11 MPa, 600 ° C and expands to 1 MPa, where some of the steam is extracted and diverted to the open feedwater heater operating at 1 MPa. The remaining steam expands through the second turbine stage to a condenser pressure of 6 kPa. Saturated liquid exits the open feedwater heater at 1 MPa. The net power output is 264 MW. Determine (a) the thermal efficiency of the cycle, (b) the mass flow rate into the first turbine stage and (c) the fraction of flow extracted where bleeding occurs. (d) What-if Scenario: What would the net power developed be if the bleeding pressure were increased to 1.2 MPa?[E

A power plant operates on a regenerative vapor power cycle with one open feedwater heater. Steam enters the first turbine stage at 11 MPa, 600 ° C and expands to 1 MPa, where some of the steam is extracted and diverted to the open feedwater heater operating at 1 MPa. The remaining steam expands through the second turbine stage to a condenser pressure of 6 kPa. Saturated liquid exits the open feedwater heater at 1 MPa. The net power output is 264 MW. Determine (a) the thermal efficiency of the cycle, (b) the mass flow rate into the first turbine stage and (c) the fraction of flow extracted where bleeding occurs. (d) What-if Scenario: What would the net power developed be if the bleeding pressure were increased to 1.2 MPa?[E

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider a regenerative power cycle with an open feedwater heater. water vapor enters the turbine at 8.0 MPa, 480°C and expands to 0.7 MPa where part of this vapor is extracted and presented to the open feedwater heater operating at 0.7 MPa. The rest of the steam expands in the second stage of the turbine to the condenser pressure of 0.008 MPa. The condenser outlet is saturated liquid at 0.7 MPa. The isentropic efficiency of each turbine stage is 85% and each pump operates isentropically. If the net power of the cycle is 100 MW, determine:1.Thermal performance and2. The mass flow of steam entering the first stage of the turbine, in kg/h.
An ideal regenerative steam power cycle operates with steam that enters the turbine at 30 bars and 500°C and leaves the condenser as a saturated liquid at 0.1 bar. A single closed feed water heater is used with steam entering at 5 bars. Determine the thermal efficiency of the cycle
A steady-state system for producing power consist of a pump, heat exchanger and a turbine. Watersteam power plant operates on an ideal reheat– regenerative Rankine cycle. Steam enters the highpressure turbine at 10 MPa and 550°C and leaves at 0.8 MPa. Some steam is extracted at thispressure to heat the feedwater in an open feedwater heater. The rest of the steam is reheated to500°C and is expanded in the low-pressure turbine to the condenser pressure of 10 kPa. Determinethe entropy generation associated with the reheating and regeneration processes. Assume a sourcetemperature of 1800 K. please i so another solution for this qustion and they didn't do any calculation for state 4 can i know why?
Please solve the following
Water is the working fluid in a supercritical ideal reheat cycle. Steam enters the first-stageturbine at 320 bar, 640°C, and expands to 120 bar. After being reheated it enters thesecond-stage turbine at a temperature of 600°C, where is expands to a pressure of 0.06bar. The steam is then condensed until it is a saturated liquid.Question:Determine:(a) The thermal efficiency of the cycle(b) The back work ratio of the cycle
I need the answer as soon as possible
6.2) There is a regenerative cycle that uses steam as the working fluid. Steam leaves the boiler and enters the turbine at 4 MPa and 400°C. After an expansion to 400 kPa, part of the steam is withdrawn from the turbine in order to heat the feedwater in an open feedwater heater (FWH). The pressure in the heater is 400 kPa, the water that leaves is a saturated liquid at 400 kPa, and the non-extracted steam expands at 10 kPa. Determine the efficiency of the cycle Boiler Turbine T Water boiler Condenser B Pump 2 Be Pump 1 Ans: Ans: NT-37%
1) In an ideal regenerative Rankine cycle, vapor enters the turbine at 7MPa and 550°C. Steam first expands to 0.8MPa where some of the steam is extracted and transferred to an open feedwater heater (FWH) operating at 0.8MPa. The remaining steam expands through the second-stage turbine to the condenser pressure of 10kPa. Saturated liquid exits the open FWH at 0.8MPa and water enters pump I as a saturated liquid. Determine a) the power output of the cycle in kJ/kg b) the thermal efficiency of the cycle c) the heat transfer from the condenser to the environment, in kJ/kg. Boiler Pump II Open FWH Pump 1 Turbine Condenser
A steady-state system for producing power consist of a pump, heat exchanger and a turbine. Watersteam power plant operates on an ideal reheat– regenerative Rankine cycle. Steam enters the highpressure turbine at 10 MPa and 550°C and leaves at 0.8 MPa. Some steam is extracted at thispressure to heat the feedwater in an open feedwater heater. The rest of the steam is reheated to500°C and is expanded in the low-pressure turbine to the condenser pressure of 10 kPa. Determinethe entropy generation associated with the reheating and regeneration processes. Assume a sourcetemperature of 1800 K. Please Solve step by step.
Scenario (1) The first steam power plant operates on an ideal reheat Rankine cycle. Steam enters the first turbine at 8 MPa and 500 C and leaves at 3 MPa. Steam is then reheated at a constant pressure to 500 C before it expands to 20 kPa in the low-pressure turbine. Assuming that heat is being added to the boiler from a high temperature source at 1800 K and the condenser is transferring heat to a temperature sink at 300 K. Task 1 Investigate the effect of changing pump efficiency on the overall thermal efficiency of the thermodynamics cycle (Hint: You will assume different values for the isentropic pump efficiency such as: 70%, 80%, 90%, 95%, and 100%, then observe how it will change the thermal efficiency of the cycle). Representing the results in a plot is recommended.
Scenario (1) The first steam power plant operates on an ideal reheat Rankine cycle. Steam enters the first turbine at 8 MPa and 500 C and leaves at 3 MPa. Steam is then reheated at a constant pressure to 500 C before it expands to 20 kPa in the low-pressure turbine. Assuming that heat is being added to the boiler from a high temperature source at 1800 K and the condenser is transferring heat to a temperature sink at 300 K. Task 1 Investigate the effect of changing turbine efficiency on the overall thermal efficiency of the thermodynamic cycle. (Hint: You will assume different values for the isentropic turbine efficiency such as: 70%, 80%, 90%, 95%, and 100%, then observe how it will change the thermal efficiency of the cycle). Representing the results in a plot is recommended.
Consider a water-ammonia binary vapor cycle consisting. In the steam cycle, superheated vapor enters the turbine at 7 MPa, 450C, and saturated liquid exits the condenser at 55C. The heat rejected from the steam cycle is provided to the ammonia cycle, producing saturated vapor at 45C, which enters the ammonia turbine. Saturated liquid leaves the ammonia condenser at 1 MPa. For a net power output of 24 MW from the binary cycle, determine (a) the mass flow rates for the steam and ammonia cycles, respectively, in kg/s, (b) the power output of the steam and ammonia turbines, respectively, in MW. (c) the rate of heat input to the ammonia cycle, in MW, (d) the rate of heat addition to the binary cycle, in MW, and (e) the thermal efficiency of the binary vapor cycle.