A power diode has a reverse saturation current of 10−8 A and n =2. What is the forward voltage drop at the peak current of 100 A? What is the power dissipation in the diode in a half-wave rectiﬁer application operating at 60 Hz if the series resistance is 0.01 Ω and the conduction time is 1 ms?

A power diode has a reverse saturation current of 10−8 A and n =2. What is the forward voltage drop at the peak current of 100 A? What is the power dissipation in the diode in a half-wave rectiﬁer application operating at 60 Hz if the series resistance is 0.01 Ω and the conduction time is 1 ms?

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter12: Electronic Control Devices

Section: Chapter Questions

Problem 3RQ: Diodes and rectifiers allow current to _________. flow in one direction only flow in both...

See similar textbooks

Similar questions

Diodes and rectifiers allow current to _________. flow in one direction only flow in both directions divide paths of flow none of the above
What could happen if the diode's type would be changed from silicon to germanium? in Clipping circuts experiment
A clipper circuit based on diodes are simple way to modify waveform in mechatronics. Assume that the two diodes shown in the circuit below are ideal diodes. If the input voltage in the circuit is a 1 kHz sinusoid with peak amplitude of 8V, sketch the Va.. (t) 10 kO 8V 10 kO Vin Vin(t) D2 Vout(t) RL Ims D1 6V -8V 4V Page | 1
A power diode has a reverse saturation current of 10−9 A and n = 1.6. What is the forward voltage drop at the peak current of 48.6 A .
In the circuit below, Vi = 6sin (wt) and diodes are considered ideal diodes. Describe the working principle in detail by drawing the output signal. 10KO D2 10KO V. VaC D1 4V 2V
//sketch the output wave form of the below. The input voltage circuit shown varies from "0" to "150V" linearly, Assame the diodes are ideal. D₂ Vi gül DI * + 300 - look 3200K. I+ I 10ου + vo.
The given figure shows a step-down dc chopper. A freewheeling diode is placed across the load. The TON would be TOFF load current varies between the limits of 10 A. The time ratio 100V KH 40 mH vvvvv io 5Q
The current through the diode in the circuit given in the Figure below when Vy = 0.7 V is? ww 8092 12V Select one a. 24.26 mA b. 13.09 mA c. 58.23 mA d. 40.13 mA 40-52 ww 3092 ID
Two germanium diodes are connected in series and have a load resistance of 10 kQ and a forward supply voltage of 5 V. Calculate the voltage across the load resistor. * O 4.7 V O 4.4 V O 0.3 V 0.6 V
Refer to figure below, if the input A is more positive than input B, which diodes will be conducting? F1 AO D2 AC Input Load D3 D4 BO O D1 and D4 D2 and D3 O D1 and D3 D3 and D4 D1
Design a clamper to perform the function indicated below. Silicon diodes 10 V 2.7 V -10 V -173 V
A clipper circuit based on diodes are simple way to modify waveform in mechatronics. Assume that the two diodes shown in the circuit below are ideal diodes. If the input voltage in the circuit is a 1 kHz sinusoid with peak amplitude of 8V, sketch the Vaue (t). 10 k. 8V 10 kN. D2 RL Vourlt) Vin= Vin(t) Ims D1 6V -8V 4V Page | 1