A portion of the main program to call a subroutine SUB in an 8085 environment is given below. : : LXID, DISP LP: : CALL SUB It is desired that control be returned to LP + DISP + 3 when the RET instruction is executed in the subroutine. The set of instructions that precede the RET instruction in the subroutine are

A portion of the main program to call a subroutine SUB in an 8085 environment is given below. : : LXID, DISP LP: : CALL SUB It is desired that control be returned to LP + DISP + 3 when the RET instruction is executed in the subroutine. The set of instructions that precede the RET instruction in the subroutine are

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

VBE (on=Vac (RA) = 0.7V, V (sat) = 0.8V, Ve (sat= 0.15V,Vp (0n)=0.3V, 0 = 0.85, B = 0.25 %3D SED Q4. Open collector logic gate is shown in Figure. What logic function is performed by this circuit? | R F B O a. A B O b. A B A B O d. А. В O e. A· B А. В
How many bits are required to represent the Arduino analog input?Hint: There are 1024 possible values.Explain.
Q1) For the circuits shown in figures 1 and 2: 1. What is the function of output? 2. Find the max. and min. Vol. value? 3. Determine the static power (avg.)? 4. Design equivalent logic circuit by CMOC logic circuits? Use VDD= 10 V. Vr.o=1V. Vru-1V. (W/L)o= (5/2), (W/L)L (20/2), RD = 40k, KL = 10P A/V^2 and KO = 40pA/V`2? Figure 1 5 VDD RD Figure 2 बदना दे
What are the necessary steps one must take when designing a logic circuit from a description of the problem?
Explanation about (Deal with operational amplifier controllers and programmable logic controllers)
If R0 = 0x20008000, after run STMDB r0!, {r3, r9, r7, r1, r2} command what is the r7 register memory start address?A. R0= 0x20007ff4B. R0 = 0x20007ffefC. R0 = 0x20007fffD. R0=0x20007fecE. R0 = 0x20007ff0
A. Write a Verilog HDL code for Verilog code for a for 6-bit unsigned up counter B. Write test bench code of the circuit in the figure: DỊ40) 5-bit Full Adder 5-bit 5-bit Up - Counter DFF Ck
Write an assembly language program in microprocessor 8085 so that I can fetch 2 8 bit numbers from memory locations and store the product, whether it's 8 bit or 16 bit, in 2 different memory locations. I am aware with programming logic. So, only give me the working program and attach a snapshot of the output. No need to explain.
A 16-bit successive approximation ADC is to be designed to operate at 50,000 conversions/second. What is the clock frequency? How rapidly mustthe unknown and reference voltage switches change state if the switch timing delay is to be equivalent to less than 0.1 LSB time?
1- Explain the meaning and operation of CMC instruction ? 2. The Instruction Pointer is bits in length. a) 8 bits b) 4 bits c) 16 bits d) 32 bits
a) In Assembly programming what is the functionality of the following instructions DECFSZ ВTESC MOVLW MOVWF goto b) A piece of code is required for a time critical activity. Should this be written in assembly language or C? Explain your answer. 5 Explain the difference between the (For) and (While) loops. Highlight the main components of the (For) loop that are required for its execution. Consider the following C program designed to run on a PIC 18F4455. int main(void) 2 { 1 double voltage; double current; double milliwatts; double energyUsed; double cummulativeEnergy = 0; while (1) { voltage=analogRead (VOLTAGE_PIN)*voltageScaleFactor; current=analogRead (CURRENT_PIN)*currentScaleFactor; milliwatts=voltage*current; energyUsed=milliWatts*0.5; cummulativeEnergy=cummulativeEnergy+energyUsed; 10 11 12 13 14 15 _delay_ms (500); 16 } 17 a) What is the role of the symbols "{" and "}" b) The code here is indented. Explain the importance of indentation N m 4 n Or 00 o A m
A) List and describe 10 features of the Atmel ATmega 2560 AVR microcontroller (use the ATmega 2560 complete reference manual for help). B) List and describe two AVR instructions. As part of your description make sure that you list the operation for each instruction that is provided in the instruction set summary.