A portion of the Fe-C equilibrium phase diagram is shown below. A steel containing 0.76wt% C is held at 900° in the single phase, Austenite region. Describe the change in structure that occurs as this alloy is cooled to a temperature of 700°C. 1100 1000 Y. 900 y+ Fe,C 800 a+y 727°C 700 0.76 2.14 0.022 600 500: a+ Fe,C 400 0. 1.0 2.0 Composition (wt % C) Temperature ("C)

Q: A canon is used to fire a bomb with velocity 20 m/s. If angle of projection is varied from 20…

A:

Q: t(s) Problem 4 Write a relationship between the velocities of blocks A, B, C. If A is traveling…

A:

Q: Q3:- The Fig. below shows an epicyclic gear train in which the gear D is held stationary by shaft A…

A:

Q: Calculate the velocity of a 4 inch diameter piston when 3 gallons per minute enter cylinder. Find…

A:

Q: 3. As shown in the Figure 12, for the variable speed cylinder, a and b are the oil inlet andc is the…

A: Given Data

Q: Compute the force that must be applied to prevent the cart in the figure from accelerating. The…

A: Here, we will use impulse-momentum equation to find the force. The force that needs to apply will be…

Q: The motor turns gear A with a constant angular acceleration, alpha (a) = 4.5 rad/s^2, starting from…

A:

Q: In the figure shown, If vo=500 mm/s, solve for the (a) velocity (in m/h) of D and (b) the angular…

A:

Q: 10) An automobile is driven by at 30kph for 12 min , then at 40 kph at 4 min and finally at 50kph at…

A: Given data: V1=30 kpht1=12 min=0.2 hourV2=40 kpht2=0.0667 hourV3=50 kpht3=0.1667 hour Need to…

Q: Problem Compute the kinetic energy of an 3046 lb. Automobile travelling at 104 mi/hr, ) How many…

A:

Q: ▸ A Pelton wheel of 1 meter diameter is working under a head of 550 meter. Find the speed of the…

A:

Q: 7. Find the power to pull a a 50kg upward a constant velocity of 13m/s,

A:

Q: QI/ (a) A car moving at a constant speed of 54 km/hr over a distance of 300 m. Calculate the time…

A: According to the details provided in the question,  we need to calculate parts a, b  and c  I am…

Q: Link ABC in the figure below has wheels at point A and B which remain in contact on the horizontal…

A:

Q: A car has wheels with 1m diameter. Calculate the vehicle speed in km/h when angular speed of the…

A:

Q: Find all the velocities if distance is 4m and time is 5s

A: Given:distance=4 mtime=5 sec

Q: Write differential pressure between points A&B (PA-PB) for bellow system. Jump across Z2 P2- Z2. P2…

A:

Q: Problem 3 (33) When the roller coaster is at point B as shown in the figure below it has a speed of…

A:

Q: a 200N black is at rest on a 30° incline the coefficient of friction (0.2) compute the value of a…

A: Given,  Weight of the block , W = 200 Angle of inclination , θ = 30 Coefficient of friction ,μ =…

Q: 1- Calculate the value of the force acting on a car with a mass of 1800 kg and an acceleration of 8…

A: Mass of the car, m = 1800 kgacceleration, a = 8 m/s²

Q: Q2: A particle is thrown at an angle of 30° with velocity of 36 kmph calculate its time of flight…

A: Given data: Initial velocity, u = 36 km/h. The angle of throwing the particle, Ɵ = 30°. Convert…

Q: A boat is pulled toward a dock by a rope from the bow through a ring on the dock (6 ft) above the…

A: Given data: -  The height of the dock is h = 6 ft. The pulling rate of the rope is dr/dt = 3 ft/s.…

Q: In the figure shown, If vç=700 mm/s, solve for the (a) velocity (in m/h) of D and (b) the angular…

A: Find the velocity of D and angular velocity of AB.

Q: Determine the total distance traveled until the car stops. show it with solution. thank you!

A:

Q: Find the initial velocity of car if final velocity is 100 m/s, acceleration 20 m/s2 time 3 s

A:

Q: a new computer drive is proposed to have a disc, as shown in the figure below. The disc is to rotate…

A: cgdg

Q: Q3- A projectile is fired from point A which is at a height of (1.2 m). The projectile must hit…

A: given data;

Q: Question 3: a Ina roller coaster the ride includes a vertical drop of 120 m. Sup has a speed of 4.0…

A:

Q: Use 3 decimal places The 250-N block rests upon a level plane for which fk = 0.2. It is pulled by…

A:

Q: Q3:- The Fig. below shows an epicyclic gear train in which the gear D is held stationary by shaft A…

A: given:ZF=40ZG=30ZE=20NB=200rpmAS SHAFTS F AND E ARE AT SAME AXIS AND SHAFTS G AND D ARE AT SAME…

Design of Shafts and Shaft Components

The shaft is basically defined as the machine element that rotates, is in circular cross-section, it is majorly used to transfer the power from one part of the system to another, or from a power generating machine to a power absorbing machine. The shaft is supported on bearings and is rotated with the help of a set of gears or pulleys that are used for the power transmission. Bending moment, torsion, and an axial force act upon the shaft. Designing of shaft primarily involves determining stresses at a critical point in the shaft that is arising due to loading.